R A. The failure message is generated if channel A sensor signal is invalid or R out of range. R NOTE : If T3 sensor Part Number is 1348M21P01, P04 or P05, replace T3
____ R sensor (Ref. AMM TASK 77-23-10-000-001) and (Ref. AMM TASK 77-23-10-400-001).
F 『
∞∞77-20-00∞∞∞∞∞∞∞∞∞∞Page 219
EEFF : ALL E
E E Aug 01/99
E E
ECES E
F 『
E C F M E
E E
E 56 E
E E
R (1) If the failure message T3 SNSR, J13, ECU is not confirmed: R - no maintenance action is required.
R (2) If the failure message T3 SNSR, J13, ECU is not confirmed, but is R repetitive: R - visually examine the T3 thermocouple receptacle and the CJ13 R harness connector for damaged pins and contamination (Ref. AMM TASK
73-21-50-210-001).
R (a) If harness connector or T3 thermocouple receptacle is damaged: R - repair or replace as required.
R (b) If no damage is found: R - visually examine the ECU (4000KS) receptacle and the HJ13 R harness connector for damaged pins and contamination (Ref. AMM
TASK 73-21-50-210-001).
R 1_ If harness connector or ECU receptacle is damaged:
R - repair or replace as required.
R 2_ If no damage is found:
R - replace the T3 thermocouple (Ref. AMM TASK 77-23-10-000-002)
R and (Ref. AMM TASK 77-23-10-400-002).
R (c) If the fault continues during the subsequent flights:
R - replace the CJ13 harness (Ref. AMM TASK 73-21-50-000-029) and
R (Ref. AMM TASK 73-21-50-400-029).
R (d) If the fault continues during the subsequent flights:
R - replace the HJ13 harness (Ref. AMM TASK 73-21-50-000-046) and
R (Ref. AMM TASK 73-21-50-400-046).
R (e) If the fault continues during the subsequent flights:
R - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and
R (Ref. AMM TASK 73-21-60-400-001).
R (3) If the failure message T3 SNSR, J13, ECU is confirmed:
R - disconnect the two CJ13 connectors from the T3 thermocouple
R - visually examine the T3 thermocouple receptacle and the CJ13
R harness connectors for damaged pins and contamination (Ref. AMM
TASK 73-21-50-210-001).
R (a) If harness connectors or T3 thermocouple receptacle are damaged:
R - repair or replace as required.
R (b) If no damage is found:
R - do a resistance check of the two T3 thermocouple connectors
R between:
R . pins A and B (0.5 to 10 ohms)
R . pin A and the ground (> 10 megohms).
F 『
∞∞77-20-00∞∞∞∞∞∞∞∞∞∞Page 220
EEFF : ALL E
E E Aug 01/99
E E
ECES E
F 『
E C F M E
E E
E 56 E
E E
1 If the resistance values of one of the two T3 thermocouple
_ connectors are out of specified limits:
- replace the T3 thermocouple (Ref. AMM TASK 77-23-10-000-002) and (Ref. AMM TASK 77-23-10-400-002).
2 If the resistance values are in the specified limits:
_
- reconnect the CJ13 harness to the T3 thermocouple
- disconnect the HJ13 harness from the ECU
- visually examine the ECU (4000KS) receptacle and the HJ13 harness connector for damaged pins and contamination (Ref. AMM TASK 73-21-50-210-001).
a If harness connector or ECU receptacle is damaged:
_
- repair or replace as required.
b If no damage is found:
_
- do an electrical resistance test through the HJ13 harness between: . pins 4 and 5 (0.5 to 10 ohms)
R . pins 14 and 15 (0.5 to 10 ohms) . pins 4 and 16 (> 10 megohms) . pins 14 and 16 (> 10 megohms) . pin 4 and the ground (> 10 megohms) . pin 14 and the ground (> 10 megohms).
c If the resistance values are in the specified limits:
_
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
d If the resistance values are out of the specified limits:
_
- reconnect the HJ13 harness
- disconnect the HJ13 harness from the CJ13 harness at the 6 o'clock junction box
- do an electrical resistance test through the CJ13 harness between: . pins 7 and 8 (0.5 to 10 ohms) . pins 1 and 10 (0.5 to 10 ohms) . pins 7 and 9 (> 10 megohms) . pins 1 and 9 (> 10 megohms) . pin 7 and the ground (> 10 megohms) . pin 1 and the ground (> 10 megohms).
e If the resistance values are out of the specified limits:
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 发动机指示(172)
