(b) If the resistance values are out of the specified limits:
- remove the harness J9 or J10 from SAV and do a check of the SAV resistance between: . pins 1 and 2 (10 to 60 ohms).
1 If the resistance values are in the specified limits:
_
- replace the harness J9 (Ref. AMM TASK 73-21-50-000-008) (Ref. AMM TASK 73-21-50-400-008) or
- replace the harness J10 (Ref. AMM TASK 73-21-50-000-009) (Ref. AMM TASK 73-21-50-400-009).
2 If the resistance values are out of the specified limits:
_
- replace the starter shutoff valve (SAV) (Ref. AMM TASK 80-11-20-000-001) (Ref. AMM TASK 80-11-20-400-001).
3 If the fault continues:
_
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) (Ref. AMM TASK 73-21-60-400-001).
B. Do the test given in Para. 3.A.(1).
F 『 EEFF : ALL E ∞∞77-00-00∞∞∞∞∞∞∞∞∞∞Page 299
E E Nov 01/04 ERE
ECES
F 『
E C F M E
E E
E 56 E
E E
TASK 77-00-00-810-889
Failure of the Starter Shutoff Valve on Engine 2
1. Possible Causes
_______________
- starter shutoff valve (SAV)
- starter
- harness J9
- harness J10
- ECU (4000KS)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 73-21-50-000-008 Removal of the J9 Harness AMM 73-21-50-000-009 Removal of the J10 Harness AMM 73-21-50-400-008 Installation of the J9 Harness AMM 73-21-50-400-009 Installation of the J10 Harness AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)(4000KS) AMM 73-21-60-400-001 Installation of the Electronic Control Unit
(ECU)(4000KS) AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with
Engine non Motoring)
AMM 80-11-10-000-001 Removal of the Pneumatic Starter
AMM 80-11-10-400-001 Installation of the Pneumatic Starter
AMM 80-11-20-000-001 Removal of the Starter Shutoff Valve
AMM 80-11-20-400-001 Installation of the Starter Shutoff Valve
3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the FADEC 2A and 2B on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
4. Fault Isolation
_______________
A. If the fault sypmtom is identified by the upper ECAM warning START AIR, SAV and the test of the FADEC 2A and 2B gives no CFDS maintenance message:
- do a check for open or short to ground at pins J9/11, 12 or J10/11, 12 of the harness J9 or J10 between the ECU (4000KS) and the starter shutoff valve.
(1) If the wiring is not correct:
- repair the above wiring.
F 『 EEFF : ALL E ∞∞77-00-00∞∞∞∞∞∞∞∞∞∞Page A200
E E Nov 01/04 ERE ECES
F 『 E C F M E E E E 56 E E E (2) If the wiring is correct:
- disconnect the harness J9 or J10 from the ECU (4000KS) and do a check of the ECU resistance cable between: . pins 11 and 12 (10 to 60 Ohms).
(a) If the resistance values are in the specified limits:
- do a check for low starter air duct pressure.
1 If the starter air duct pressure is in the specified limits
_
(11 PSI < P < 60 PSI):
- replace the starter shutoff valve (SAV) (Ref. AMM TASK 80-11-20-000-001) (Ref. AMM TASK 80-11-20-400-001)
- replace the starter (Ref. AMM TASK 80-11-10-000-001) (Ref. AMM TASK 80-11-10-400-001).
(b) If the resistance values are out of the specified limits:
- remove the harness J9 or J10 from SAV and do a check of the SAV resistance between: . pins 1 and 2 (10 to 60 Ohms).
1 If the resistance values are in the specified limits:
_
- replace the harness J9 (Ref. AMM TASK 73-21-50-000-008) (Ref. AMM TASK 73-21-50-400-008) or
- replace the harness J10 (Ref. AMM TASK 73-21-50-000-009) (Ref. AMM TASK 73-21-50-400-009).
2 If the resistance values are out of the specified limits:
_
- replace the starter shutoff valve (SAV) (Ref. AMM TASK 80-11-20-000-001) (Ref. AMM TASK 80-11-20-400-001).
(3) If the fault continues:
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) (Ref. AMM TASK 73-21-60-400-001).
B. Do the test given in Para. 3.A.
F 『 EEFF : ALL E ∞∞77-00-00∞∞∞∞∞∞∞∞∞∞Page A201
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 发动机指示(106)
