R 3_ If the resistance values are out of the specified limits:
R - replace the alternator stator (Ref. AMM TASK 73-21-30-000-R 001) and (Ref. AMM TASK 73-21-30-400-001).
R 4_ If the resistance values are in the specified limits:
R - reconnect the J9 harness to the alternator stator.
R - disconnect the J9 harness from the ECU (4000KS) receptacle.
R - Visually examine the ECU (4000KS) receptacle and the J9
R harness connector for damaged pins or contamination (Ref.
R AMM TASK 73-21-50-210-002).
R a_ If harness connector or ECU receptacle is damaged:
R - repair or replace as required.
R b_ If no damage is found:
R - do an electrical resistance test through the J9 harness
R between:
R . pins 5 and 13 (<1 Ohm)
R . pins 5 and 14 (<1 Ohm)
R . pins 5 and 15 (<1 Ohm)
R . pins 5 and 4 (>10 megohms)
R . pins 13 and 4 (>10 megohms)
R . pins 14 and 4 (>10 megohms)
R . pins 15 and 4 (>10 megohms)
R . pin 5 and the ground (>10 megohms)
F 『
∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page A211
EEFF : ALL E
E E May 01/03
E E
ECES E
F 『
E C F M E
E E
E 56 E
E E
R
R * If the resistance values are out of the specified
R limits:
R - replace the J9 harness (Ref. AMM TASK 73-21-50-000-042)
R and (Ref. AMM TASK 73-21-50-400-042).
R
R * If the resistance values are in the specified limits:
R - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-
R 001) and (Ref. AMM TASK 73-21-60-400-001).
R D. Do the test given in Para. 3.A.
(1) No additional maintenance action is required if the fault is not
confirmed.
(2) Repeat the fault isolation procedure if the fault continues.
F 『 EEFF : ALL E ∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page A212
E E May 01/03 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
TASK 77-10-00-810-847
Loss of the ECU Cross Channel on Engine 1 - Channel B
1. Possible Causes
_______________
R R - Alternator Stator R - Accessory Gearbox Assembly R - Alternator Rotor R - J10 Harness R - ECU (4000KS)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
R AMM 72-63-00-000-003 Removal of the Accessory Gearbox Assembly
R AMM 72-63-00-400-003 Installation of the Accessory Gearbox Assembly
R AMM 73-21-30-000-001 Removal of the Control Alternator
R AMM 73-21-30-400-001 Installation of the Control Alternator
R AMM 73-21-50-000-043 Removal of the HJ10 Harness
R AMM 73-21-50-210-002 Visual Inspection of the Wiring Harnesses
R AMM 73-21-50-400-043 Installation of the HJ10 Harness
R AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)
R AMM 73-21-60-400-001 Installation of the Electronic Control Unit (ECU)
AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with
Engine non Motoring)
R AMM 79-00-00-281-002 Check of the Electrical Master Chip Detector for
R Particles
3. Fault Confirmation__________________
A. Do the operational test of the FADEC 1B on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
4. Fault Isolation
_______________
R A. If the failure message ECU (B CHANNEL) is not confirmed:
R - no maintenance action is required.
R NOTE : This failure message is generated when there is an internal ECU
____
R cross channel fault, control alternator stator contact, or related
R wiring.
R
F 『
∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page A213
EEFF : ALL E
E E May 01/03
E E
ECES E
F 『
E C F M E
E E
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 发动机指示(160)
