2 If no damage is found:
_
- do the electrical resistance test through the HJ8 harness between: . pins 2 and 11 (40 to 80 ohms) . pins 2 and 3 (>10 megohms)
R . pin 2 and the ground (>10 megohms).
a If the resistance values are in the specified limits:
_
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
b If the resistance values are out of the specified limits:
_
- replace the HJ8 harness (Ref. AMM TASK 73-21-50-000-041) and (Ref. AMM TASK 73-21-50-400-041).
B. Do the test given in Para. 3.A.
(1) No additional maintenance action is required if the fault is not confirmed.
(2) Repeat the fault isolation procedure if the fault continues.
F 『 EEFF : ALL E ∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page 238
E E Aug 01/99 E E ECES
E TASK 77-10-00-810-821
F 『
E C F M E
E E
E 56 E
E E
Loss of the Feedback Signal of the N2 Speed Sensor - Engine 1 - Channel A
1. Possible Causes
_______________
- SENSOR-N2 ROTATIONAL SPD (4001EV)
- ECU (4000KS)
- HJ7 harness
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific bristle brush
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP2011 * stoddard solvent (Ref. 70-30-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 73-21-50-000-040 Removal of the HJ7 Harness AMM 73-21-50-210-002 Visual Inspection of the Wiring Harnesses AMM 73-21-50-400-040 Installation of the HJ7 Harness AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU) AMM 73-21-60-400-001 Installation of the Electronic Control Unit (ECU) AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with
Engine non Motoring) AMM 77-11-20-000-002 Removal of the N2 Speed Sensor (4001EV). AMM 77-11-20-400-002 Installation of the N2 Speed Sensor (4001EV).
3. Fault Confirmation
__________________
A. Do the operational test of the FADEC 1A on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
F 『 EEFF : ALL E ∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page 239
E E Aug 01/99 ERE
ECES
F 『
E C F M E
E E
E 56 E
E E
4. Fault Isolation
_______________
A. The failure message is generated if channel A input from the N2 sensor is invalid or out of range.
(1) If the failure message N2 SNSR, J7, ECU is not confirmed: R
R (a) No maintenance action is required.
(2) If the failure message N2 SNSR, J7, ECU is not confirmed but is repetitive:
- disconnect HJ7 harness from the N2 sensor (N2-A connector).
R (a) Visually examine the receptacle and the connector for damaged R pins or contamination (Ref. AMM TASK 73-21-50-210-002).
1 If damage is found:
_ - repair or replace as required.
2 If no damage is found:
_
- do a cleaning of the connector and receptacle using a bristle brush with stoddard solvent (Material No. CP2011) (Ref. AMM TASK 73-21-50-210-002).
(b) If the failure continues during the subsequent flights:
- replace the SENSOR-N2 ROTATIONAL SPD (4001EV) (Ref. AMM TASK 77-11-20-000-002) and (Ref. AMM TASK 77-11-20-400-002).
(c) If the failure continues during the subsequent flights:
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
(d) If the failure continues during the subsequent flights:
- replace the HJ7 harness (Ref. AMM TASK 73-21-50-000-040) and (Ref. AMM TASK 73-21-50-400-040).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 发动机指示(130)
