A. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 32-00-00Page 204 1 1 Aug 01/05 1 1 1CES 1
TASK 32-00-00-481-002 Installation of the Safety Devices on the Landing Gear Doors WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : MAKE SURE THAT THE WHEEL CHOCKS ARE IN POSITION.
_______
1. Reason for the Job
__________________
R R Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
460005835 2 GROUND LOCK SLEEVE
98D32203502000 2 SAFETY PIN - NLG DOOR
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-12-00-010-001 Open the Main Gear Doors for Access
32-22-00-010-001 Nose Gear Doors - Ground Doors Opening
32-00-00-991-003 Fig. 202
1EFF : ALL 1 32-00-00Page 205 1 1 Feb 01/04 1 1 1CES 1 1EFF : ALL 1 32-00-00Page 206 1 1 May 01/98 1 1 1CES 1
3. Job Set-up__________
Subtask 32-00-00-860-052
A. Aircraft Maintenance Configuration
(1) Open the applicable MLG door(s) (Ref. TASK 32-12-00-010-001).
(a) Make sure that the piston rod of the MLG door actuating cylinder is clean.
(2) Open the NLG doors (Ref. TASK 32-22-00-010-001).
4. Procedure_________
Subtask 32-00-00-481-051
R R A. Installation of the Safety Devices on the Landing Gear Doors (Ref. Fig. 202/TASK 32-00-00-991-003)
R (1) To install the safety devices on the MLG doors:
(a) Remove the pins (1) and open the GROUND LOCK SLEEVE (460005835).
(b) Make sure that the GROUND LOCK SLEEVE is in a clean and correct condition.
(c) Put a GROUND LOCK SLEEVE in position on the piston rod of each of the MLG door actuating cylinders.
(d) Close the GROUND LOCK SLEEVE and install the pins (1) from the top.
(e) Make sure that the flag is in view.
R (2) To install the NLG safety devices:
(a) Make sure that the holes in the NLG doors and the hinges are aligned.
(b) Make sure that each SAFETY PIN - NLG DOOR is in a clean and correct condition.
(c) Install a SAFETY PIN - NLG DOOR (98D32203502000) through the holes in each NLG door and hinge.
(d) Make sure that the flag is in view.
Main and Nose Landing-Gear Doors Safety-Devices Figure 202/TASK 32-00-00-991-003
1EFF : 1 1R 1CES ALL 1 11 1 32-00-00 Page 207 May 01/98
5. Close-up
________ Subtask 32-00-00-942-059
A. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 32-00-00Page 208 1 1 May 01/98R 1 1 1CES 1
TASK 32-00-00-481-003
To Make the Landing Gear and the Doors Safe after a Free-Fall Extension
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架1(80)
