A320飞机维护手册 AMM LANDING GEAR 起落架1(101)_航空信息_民用航空_通用航空

曝光台注意防骗网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

(b) Examine the electrical conduits, connections, connectors and protective coverings for damage and fluid contamination. If necessary, clean the contaminated area.
R R (c) Make sure that the electrical conduits have full protection and are in a serviceable condition.
R (3) Inspect the MLG actuator:
(a) Examine the actuator for signs of hydraulic leaks.
(b) Examine the chrome plating on the ram for wear, scoring and damage.
(c) Examine the actuator for damage to the protective finish.
(d) Examine the actuator for cracks, dents, distortion and wear.
5. Close-up________
Subtask 32-11-00-410-050
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Remove the access platform(s).
(3) Close the MLG doors (Ref. TASK 32-12-00-410-001).
Subtask 32-11-00-942-051
B. Removal of Equipment
(1) Remove the safety barriers.
(2) Remove the warning notice(s).

(3) Remove the ground support and maintenance equipment, the special and

standard tools and all other items.
R
1EFF : ALL 1 32-11-00Page 607 1 1 Nov 01/04 1 1 1CES 1 TASK 32-11-00-220-003

Detailed Dimensional Check of the MLG Lockstay Assembly
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:

-
THE FLIGHT CONTROLS

-
THE FLIGHT CONTROL SURFACES

-
THE LANDING GEAR AND THE RELATED DOORS

-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.

1. Reason for the Job
__________________
A dimensional check of the length of the MLG lockstay actuator after replacement of:
-
a lockstay actuator

-
a side-stay assembly.

2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific non metallic scraper
No specific safety barriers
No specific warning notice
No specific access platform 2.5 m (8 ft. 2 in.)

R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft) 460006437 1 TOOL-HOLDING 460007262 1 CHECKING GAUGE
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 09-016 USA MIL-PRF-81733D TYPE II CLASS B
CORROSION INHIBITING FILLET CONSISTENCY
(Ref. 20-31-00)

1EFF : ALL 1 32-11-00Page 608 1 1 May 01/05 1 1 1CES 1

C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
8 cotter pin 32-11-17 01 -030
R 8 cotter pin 32-11-17 01A-030 8 cotter pin 32-11-17 01B-030
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
07-11-00-581-001 Lifting for Aircraft Maintenance Operations 07-11-00-586-002 Lowering of the Aircraft for Maintenance Operations 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
Configuration before Maintenance Action 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 29-14-00-614-002 Pressurization of the Hydraulic Reservoirs through
the Ground Connector 32-00-00-481-001 Installation of the Safety Devices on the Landing Gears 32-11-16-400-001 Installation of the MLG Side-Stay Assembly 2505GM,
2506GM 32-11-21-000-001 Removal of the MLG Lockstay Actuating Cylinder 32-11-21-400-001 Installation of the MLG Lockstay Actuating Cylinder 32-12-00-010-001 Open the Main Gear Doors for Access 32-12-00-410-001 Close the Main Gear Doors after Access CMM 321121 (for corrective action) 32-11-00-991-026 Fig. 601 32-11-00-991-024 Fig. 602
3. Job Set-up
__________
Subtask 32-11-00-941-062
A. Safety Precautions
(1)
Put the safety barriers in position.