Page 204 Doc # 6.02.01 09 Jan 2003 Rev. 4
25-10-00
Equipment/Furnishings
B. Install a Safety Belt
Detail Steps/Work Items Key Items/References
(1) Install the bolt and washer which attach the inertia reel and its cover to the structure. Refer to Figure 3.
(2) Install the bolt, washer plate and spring washer which attach the guide to the roll-bar. For the pilots' seats only.
(3) Put the lap straps through the holes in the seat pan. The buckle goes to the inboard side of the pilots' seats (front) and the outboard side of the passenger seat (rear).
(4) Put the lap straps between the seat pan and the metal plate. Install the bolts with washer plates from the top of the seat pan.
(5) Put the anchor plates in position on the bolts. For the pilots' seats only.
(6) Install washer plates and self-locking nuts on the bolts. Torque: 16 Nm (11.8 ft.lb).
(7) Install the seat. Refer to Paragraph 2 or 3.
5. Remove/Install the Instrument Panel Cover
A. Remove the Instrument Panel Cover
%
Detail Steps/Work Items Key Items/References
(1) Remove the screws which attach the instrument panel cover to the instrument panel and the fuselage.
(2) Lift the cover far enough to give access to the defrost hoses.
(3) Loosen the hose clamps on the defrost hoses. Remove the hoses from the cover.
(4) Lift the cover clear of the airplane.
Doc # 6.02.01 Page 205
Rev. 4 09 Jan 2003
25-10-00
AMM
B. Install the Instrument Panel Cover
Detail Steps/Work Items Key Items/References
(1) Do a check for unwanted items in the area between the firewall and the instrument panel. For example: tools.
(2) Put the instrument panel cover in position just above the instrument panel.
(3) Connect the defrost hoses to the cover.
(4) Tighten the hose clamps on the defrost hoses.
(5) Lower the cover into position on the instrument panel.
(6) Install the attaching screws.
%
6. Cleaning
A. Seats
The seat cushions are made from a fire-resistant material. Clean the cushions with a vacuum cleaner. Use a mild soap solution to remove stains. Make sure that the area is well ventilated after cleaning to remove all moisture.
B. Safety Belts
Use a mild soap solution to remove stains from the safety belts.
Page 206 Doc # 6.02.01 09 Jan 2003 Rev. 4
25-10-00
Equipment/Furnishings
Section 25-60
Emergency
1. General
This Section tells you about the optional Emergency Location Transmitter (ELT). It also tells you about % the Remote Control Panel/Indicator (RCPI) for the ACK E-01 ELT and the Remote Control Switch % (RCS) for the Jolliet JE2-NG ELT. Refer to the manufacturer's Operator’s Manual for more data.
2. Description
% A. ELT Equipment
% The ELT is located below the horizontal part of the baggage frame on the right. A bracket with one % (Jolliet) or two (ACK) quick-release clamps holds the unit in place. A bracket to the rear of the % baggage frame holds the ELT antenna. The RCPI or the RCS is located in the instrument panel,
top right.
The ELT transmits a signal automatically after a crash on the emergency frequencies of 121.5 and
243.0 Megahertz (MHz). You can operate the ELT manually for testing (see Maintenance Practices in this Section), or after an emergency landing. Maintenance on the airplane is only a visual examination of the installation (housing, mounting and antenna).
Do regular functional tests (See the Maintenance Practices in this Section).
% B. ELT Batteries
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:钻石40飞机维护手册 DA 40 SERIES AMM 2(79)