钻石40飞机维护手册 DA 40 SERIES AMM 2(32)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

(5)  On the DATE/TIME SETUP page, it may be desirable to set the date and time of the GNS 430 to aid in acquiring a GPS position.  Note that the time must be UTC time, and that the UTC date may be different from the date in the local time zone. 
CAUTION: CHANGING TO THE WRONG UTC DATE/TIME WILL DELAY SATELLITE ACQUISITION. 
(6)  No adjustments necessary on the MAIN DISCRETE INPUTS page. 
(7)  No adjustments necessary on the MAIN CDI/OBS CONFIG page except the SELECTED COURSE. Select 150° on the CDI that is connected to the GNS 430 MAIN OBS inputs. The SELECTED COURSE field should indicate near to 150° and a 'Calibrate to 150°?' field will appear. Selecting this field will calibrate the GNS 430 to match the input source.  Verify OBS operation by checking that the course displayed on the GNS 430 is within 2° of the selected course. Do this at 30° intervals around the OBS card. 
(8)  Select the COM SETUP page. These values are set at the factory and seldom require calibration. FREQ 136.975 SQ 250 26 SPACING SQ 833 19 25.0 KHz SIDETN 63  FREQ For purpose of setting the squelch and sidetone levels, only the frequencies 118.000, 127.000, and 136.975 MHz can be used. SPACING 8.33 kHz channel spacing may be required in some areas of the world. 
(9)  No adjustments necessary on the VOR DISCRETE INPUTS page. 

Page 204 Doc # 6.02.01 09 Jan 2003 Rev. 4
23-10-00
Communications
AMM

%

%
%

%
%
%
%
%
%

Detail Steps/Work Items  Key Items/References 
(10)  No adjustments necessary on the VOR/LOC/GS CDI page. 
(11)  Select thr following configuration on the VOR/LOC/GS ARINC 429 CONFIG page: RX TX SPEED Low Low SDI VOR/ILS 1 DME MODE Directed freq 2 

%

Doc # 6.02.01 Page 205
Rev. 4 09 Jan 2003

23-10-00
AMM

% 4. Configuration of the Garmin COM/NAV/GPS GNS 530
% You must configure the unit after replacing it.
% A. Configuration Mode Operation
% With power applied to the avionic rack and the GNS 530 unit turned off, press and hold the ENT % key and turn the unit on. Release the ENT key when the display activates. After the data base % page, the first page displayed is the MAIN ARINC 429 CONFIG page. While in Configuration % Mode, pages can be selected by ensuring the cursor is off and rotating the small right knob.
% To change data on the displayed Configuration Page, press the small right knob (CRSR) to turn % on the cursor. Turn the large right knob to change between data fields. Turn the large or small right % knob to change a field that the cursor is on. Once you have made the desired selection, press the % ENT key to accept the entry.
% The Configuration Pages described on the following pages are in the order found when rotating the
% right small knob starting at the MAIN ARINC 429 CONFIG page. % %

%
%
%
%
%
%
%
%

%
%
%
%
%
%
%
%
%
%
%

%
%

Detail Steps/Work Items  Key Items/References 
(1)  Select the following configuration on the MAIN ARINC 429 page: SPEED DATA IN 1 Low Off IN 2 Low Off OUT Low Off SDI Common 
(2)  Select the following configuration on the MAIN RS232 CONFIG page: INPUT OUTPUT CHAN1 Icarus-alt Off CHAN2 Off Off CHAN3 Off Off CHAN4 Off Off CHAN5 Off Off CHAN6 Off Off FUEL TYPE AV gas  When the BF Goodrich WX-500 Stormscope Option is installed in the airplane select following configuration for channel 4: INPUT OUTPUT CHAN4 WX-500 WX500 
(3)  No adjustments necessary on the MAIN INPUTS page. 

Page 206 Doc # 6.02.01 09 Jan 2003 Rev. 4
23-10-00
Communications
AMM

%

　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：钻石40飞机维护手册 DA 40 SERIES AMM 2(32)