钻石40飞机维护手册 DA 40 SERIES AMM 2(78)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

(2)  Do a check for unwanted items in the area below the seat.  For example: tools. 
(3)  Put the seat in position so that the anchor plates go through the large hole in the front main bulkhead.  Make sure that the stick gaiter does not catch on the stick top. 
(4)  Install the bolts with washer plates which attach the seat to the floor panel.  Torque: 6.4 Nm (4.7 ft.lb). 
(5)  Install the bolts with washer plates which attach the anchor plates to the front main bulkhead.  From the passenger compartment behind the pilot’s seat. Torque: 16 Nm (11.8 ft.lb). 
(6)  Fasten the press-studs which attach the seat cushion. 
(7)  Tighten the velcro at the top of the stick gaiter.  Make sure that the aileron and elevator controls are free to move throughout their range. 

3. Remove/Install the Passenger Seat
A. Remove the Passenger Seat
Detail Steps/Work Items  Key Items/References 
(1)  Release the press-studs at the front of the seat cushion.  Refer to Figure 2. Move the cushion back far enough to give access to the attaching bolts for the seat. 
(2)  Remove the 6 bolts with washer plates which attach the seat pan to the anchor plates. 
(3)  Remove the 2 bolts with washer plates which attach the front of the seat pan to the rib on top of the rear main bulkhead. 
(4)  Fold the seat-backs forward.  Lift the release catch at the left side of each seat-back. 

Page 202 Doc # 6.02.01 09 Jan 2003 Rev. 4
25-10-00
Equipment/Furnishings

(5)  Remove the 5 bolts with washer plates which attach the rear of the seat pan to the baggage compartment frame. 
(6)  Remove the two seat belt attach points in center section of seat. 
(7)  Lift the seat forward and up out of the cockpit. 

B. Install the Passenger Seat
Detail Steps/Work Items  Key Items/References 
(1)  Examine the crash elements. Look specially for delamination and buckling.  Refer to Figure 2. 
(2)  Do a check for unwanted items in the area below the seat.  For example: tools. 
(3)  Put the seat in position in the fuselage with the seat-backs folded forward.  Lift the release catch at the left side of each seat-back. 
(4)  Attach seat belt fastener to center section of seat. 
(5)  Install the 5 bolts with washer plates which attach the rear of the seat pan to the baggage compartment frame.  Torque: 6.4 Nm (4.7 ft.lb). 
(6)  Install the 6 bolts with washer plates which attach the seat pan to the anchor plates.  Torque: 16 Nm (11.8 ft.lb). 
(7)  Install the 2 bolts with washer plates which attach the front of the seat pan to the rib on top of the rear main bulkhead.  Torque: 6.4 Nm (4.7 ft.lb). 
(8)  Fasten the press-studs which hold the seat cushion. 

Doc # 6.02.01 Page 203
Rev. 4 09 Jan 2003

25-10-00
AMM

4. Remove/Install a Safety Belt
This procedure applies to the pilots' seats and the passenger seat.
A. Remove a Safety Belt
Detail Steps/Work Items  Key Items/References 
(1)  Remove the seat.  Refer to Paragraph 2 or 3. 
(2)  Remove the self-locking nuts, washer plates and bolts which attach the straps to the seat.  Refer to Figure 3. For the pilots' seats only: S Make a note of the position of the anchor plates which these bolts also hold. 
(3)  Move the straps through the holes in the seat pan and remove them. 
(4)  Release the bolt and washer which attach the inertia reel and its cover to the structure. 
(5)  Release the bolt, washer plate and spring washer which attach the guide to the roll-bar.  For the pilots' seats only. S Make a note of the position of the washers. 
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：钻石40飞机维护手册 DA 40 SERIES AMM 2(78)