钻石40飞机维护手册 DA 40 SERIES AMM 2(61)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

% CAUTION: INSTALL ONLY A BATTERY WHICH IS APPROVED BY THE % AIRPLANE MANUFACTURER.
% 2. Safety Precautions
% Obey the maintenance instructions of the battery manufacturer.
% Always disconnect the battery when you do work on the electrical system. Disconnect the negative % cable first. Connect the negative cable last.
Doc # 6.02.01 Page 201
Rev. 4 09 Jan 2003

24-34-00
AMM

% 3. Remove/Install the Battery
%
%
%
%
%
%
%
%
%
%

% A. Remove the Battery from the Airplane %

Detail Steps/Work Items  Key Items/References 
(1)  Remove the engine cowlings.  Refer to Section 71-11. 
(2)  Remove the battery retaining clamp: S Remove the 2 nuts and washers from clamp. S Lift the clamp clear of the retaining studs. 
(3)  Remove the cover from the battery box. 
(4)  Disconnect the negative cable from the battery. 
(5)  Disconnect the positive cable from the battery. 
(6)  Disconnect the vent hose from the battery. 
(7)  Remove the battery from the airplane. 

%

Page 202 Doc # 6.02.01 09 Jan 2003 Rev. 4
24-34-00
DA 40 Series
Electrical Power
AMM

%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%

%

%
%
%
%

% B. Install the Battery in the Airplane %

Detail Steps/Work Items  Key Items/References 
(1)  Make sure that the battery is clean and dry. 
(2)  Move the battery into position in the battery mount. 
(3)  Connect the vent hose to the battery. 
CAUTION: MAKE SURE THAT YOU CONNECT THE CABLES TO THE CORRECT TERMINALS. INCORRECT CONNECTION CAN DAMAGE THE ELECTRICAL AND AVIONIC SYSTEMS. 
(4)  Connect the positive cable to the battery.  Apply Dow Corning compound (DC4) to the battery terminal and the cable lug. 
(5)  Connect the negative cable to the battery.  Apply Dow Corning compound (DC4) to the battery terminal and the cable lug. 
(6)  Install the cover to the battery box. 
(7)  Install the battery retaining clamp: S Put the battery retaining clamp into position over the retaining studs and on the battery. S Install the 2 washers and nuts onto the retaining studs.  Make sure that the clamp is seated correctly. Tighten the nuts down evenly. 
(8)  Tighten the 2 retaining nuts.  Torque 1.6 Nm (1.18 ft.lb) 
(9)  Install the engine cowlings.  Refer to Section 71-11. 

%

Doc # 6.02.01 Page 203
Rev. 4 09 Jan 2003

24-34-00
AMM

% 4. Disconnect/Connect the Battery for Maintenance
%
%
%
%
%
%
%
%

% A. Disconnect the Battery for Maintenance %

Detail Steps/Work Items  Key Items/References 
(1)  Remove the engine cowlings.  Refer to Section 71-11. 
(2)  Remove the battery retaining clamp: S Remove the 2 nuts and washers from clamp. S Lift the clamp clear of the retaining studs. 
(3)  Remove the cover from the battery box. 
(4)  Disconnect the negative cable from the battery. 
(5)  Disconnect the positive cable from the battery. 

%

% B. Connect the Battery after Maintenance % %

%
%
%

%
%
%

%
%
%

%

%

%
%

%
%

%

%

Detail Steps/Work Items  Key Items/References 
CAUTION: MAKE SURE THAT YOU CONNECT THE CABLES TO THE CORRECT TERMINALS. INCORRECT CONNECTION CAN DAMAGE THE ELECTRICAL AND AVIONIC SYSTEMS. 
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：钻石40飞机维护手册 DA 40 SERIES AMM 2(61)