A. Trouble Shooting Data If available, you can print the Trouble Shooting Data (TSD) as follows:
-get access to the SYSTEM/REPORT TEST NAV page (Ref. TASK 31-32-00-860-
010). - on this page, push the line key adjacent to the MMR1 (MMR2) indication. - on the MMR1 (MMR2) page, push the line key adjacent to the TROUBLE
SHOOTING DATA indication to get the TROUBLE SHOOTING DATA page.
1EFF : ALL 1 34-36-31Page 401 1 1 Config-2 May 01/05 1 1 1CES 1
-print the TROUBLE SHOOTING DATA (TSD) page(s).
Subtask 34-36-31-865-053
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 40RT1
49VU NAV/MMR/1 42RT1 G12 FOR 40RT2
R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
121VU COM NAV/MMR/2 42RT2 L07 **ON A/C 001-049, 051-061, 101-105, 201-203,
121VU COM NAV/MMR/2 42RT2 K09 **ON A/C ALL
Subtask 34-36-31-010-052
C. Get Access
(1)
Put the access platform in position at the access door 811 in zone
122.
(2)
Open the access door 811.
4. Procedure
_________
(Ref. Fig. 401/TASK 34-36-31-991-002)
Subtask 34-36-31-020-051
A. Removal of the Multi Mode Receiver (40RT1, 40RT2)
(1)
Loosen the nuts (4).
(2)
Lower the nuts (4).
1EFF : ALL 1 34-36-31Page 402 1 1 Config-2 Aug 01/05 1 1 1CES 1
Multi Mode Receiver
Figure 401/TASK 34-36-31-991-002
1EFF : ALL 1 34-36-31Page 403 1 1 Config-2 Aug 01/01R 1 1 1CES 1
(3)
Pull the Multi Mode Receiver (1) from its rack (3) to disconnect the
electrical connectors (2).
(4)
Remove the Multi Mode Receiver (1) from its rack.
(5)
Put blanking caps on the disconnected electrical connectors (2).
1EFF : ALL 1 34-36-31Page 404 1 1 Config-2 Aug 01/01R 1 1 1CES 1
TASK 34-36-31-400-002
Installation of the Multi Mode Receiver (40RT1, 40RT2)
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
22-97-00-710-001 Operational Test of the LAND CAT III Capability
34-36-00-710-003 Operational Test of the ILS
34-36-00-740-003 BITE Test of the MMR
34-36-31-991-002 Fig. 401
3. Job Set-up
__________
Subtask 34-36-31-010-053
A. Get Access
(1) Make sure that the access platform is in position at the access door 811 in zone 122.
(2) Make sure that the access door 811 is open.
Subtask 34-36-31-865-054
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 40RT1
49VU NAV/MMR/1 42RT1 G12 FOR 40RT2
R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
121VU COM NAV/MMR/2 42RT2 L07
1EFF : ALL 1 34-36-31Page 405 1 1 Config-2 Aug 01/05 1 1 1CES 1 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
R **ON A/C 001-049, 051-061, 101-105, 201-203,
121VU COM NAV/MMR/2 42RT2 K09 **ON A/C ALL
4. Procedure
_________
(Ref. Fig. 401/TASK 34-36-31-991-002)
Subtask 34-36-31-420-051
A. Installation of the Multi Mode Receiver (40RT1, 40RT2)
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM NAVIGATION 导航3(24)
