R 1EFF : 051-099, 1 34-43-11Page 414 1 1 May 01/05 1 1 1CES 1
(11)
Install the antenna (6) on the fuselage structure (1) with the screws
(8) and the washers (7) and then tighten:
-TORQUE the screws to between 0.22 and 0.28 m.daN (19.46 and 24.77 lbf.in)
(12)
Make sure that the bonding contact resistance between the antenna (6) and the fuselage structure (1) is not higher than 5 milliohms (Ref. TASK 20-28-00-912-005).
(13)
Install the MISCELLANEOUS (Material No. 19-002) on the screw heads with the SEALANTS (Material No. 09-016) . This is necessary for the subsequent removal of the antenna.
(14)
Put a bead of SEALANTS (Material No. 09-016) around the antenna (6).
(15)
Let the sealant become dry.
(16)
Apply STRUCTURE PAINTS (Material No. 16-003) to the sealant around the antenna and the screw heads.
(17)
Apply PAINTS FOR DETAIL (INTERNAL AND EXTERN AL) (Material No. 07-001B) to the sealant of the head of the screws (8).
R **ON A/C 106-149, 201-299, 301-399, 401-499,
Subtask 34-43-11-420-050-A
A. Installation of the TCAS Antenna
(Ref. Fig. 401B/TASK 34-43-11-991-001-A)
WARNING : OBEY THE COLOR CODES WHEN YOU CONNECT THE ELECTRICAL CONNECTORS
_______ (THIS WILL PREVENT CROSS-CONNECTIONS). MAKE SURE THAT YOU INSTALL THE ANTENNA IN THE CORRECT DIRECTION. IF THE ANTENNA DOES NOT POINT IN THE CORRECT DIRECTION, THE TCAS WILL ONLY SENSE TRAFFIC BEHIND THE AIRCRAFT.
(1)
Remove the used sealant from the fuselage structure (1) with a nonmetallic scraper.
(2)
Clean the component interface and/or the adjacent area with CLEANING AGENTS (Material No. 11-004) and a lint-free cloth.
NOTE : If you install the same antenna it is necessary to clean it
____ with CLEANING AGENTS (Material No. 11-003).
R 1EFF : 051-099, 106-149, 201-299, 301-399, 1 34-43-11Page 415 1401-499, 1Aug 01/05 1 1 1CES 1
(3)
Do an inspection of the component interface and/or the adjacent area.
(4)
Put the new O-ring (4) in the correct position on the antenna (6). NOTE : If the O-ring has a flat face, make sure that this face is
____ against the antenna and not against the a/c surface.
R (5) FOR 7SG1 Install the foam washer (5).
(6)
Align the new gasket (3) with the screw holes.
(7)
Remove the blanking caps from the coaxial connectors (2) and (7).
(8)
Make sure that the electrical connectors are clean and in the correct condition.
(9)
Remove the masking tape from the coaxial cables and connect each connector (2) to the related connector (7) (see color code).
(10)
Safety the coaxial connectors (2) and (7) with corrosion-resistant-steel lockwire 0.4 mm (0.016 in.) dia..
(11)
Install the antenna (6) on the fuselage structure (1) with the screws
(9) and the washers (8) and then tighten:
-
TORQUE the four outer screws to between 0.23 and 0.33 m.daN (20.35 and 29.20 lbf.in)
-
TORQUE the four inner screws to between 0.12 and 0.16 m.daN (10.61 and 14.15 lbf.in)
(12)
Make sure that the bonding contact resistance between the antenna (6) and the fuselage structure (1) is not higher than 5 milliohms (Ref. TASK 20-28-00-912-005).
(13)
Install the MISCELLANEOUS (Material No. 19-002) (10) on the screw heads with the SEALANTS (Material No. 09-016). This is necessary for the subsequent removal of the antenna. (see detail on section B-B).
(14)
Put a bead of SEALANTS (Material No. 09-016) around the antenna (6).
(15)
Let the sealant become dry.
(16)
Apply STRUCTURE PAINTS (Material No. 16-003) to the sealant around the antenna and the screw heads.
(17)
Apply PAINTS FOR DETAIL (INTERNAL AND EXTERN AL) (Material No. 07-001B) to the sealant of the head of the screws (9).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM NAVIGATION 导航3(147)
