R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
121VU COM NAV/TCAS 4SG K10
1EFF : ALL 1 34-43-11Page 411 1 1 Aug 01/05 1 1 1CES 1R **ON A/C ALL
4. Procedure
_________
WARNING : DO NOT GET THE COMPOUND ON YOUR SKIN.
_______
IF YOU DO:
-RUB IT OFF IMMEDIATELY WITH A CLEAN CLOTH
-WASH THE SKIN WITH SOAP AND RINSE WITH CLEAN WATER. WARNING : DO NOT GET THE FLUID ON YOUR SKIN OR IN YOUR EYES. IF YOU DO:
_______
-FLUSH IT AWAY WITH CLEAN WATER
-GET MEDICAL AID.
**ON A/C 001-049, 101-105, 151-199,
Subtask 34-43-11-420-050
A. Installation of the TCAS Antenna
(Ref. Fig. 401/TASK 34-43-11-991-001)
WARNING : OBEY THE COLOR CODES WHEN YOU CONNECT THE ELECTRICAL CONNECTORS
_______ (THIS WILL PREVENT CROSS-CONNECTIONS). MAKE SURE THAT YOU INSTALL THE ANTENNA IN THE CORRECT DIRECTION. IF THE ANTENNA DOES NOT POINT IN THE CORRECT DIRECTION, THE TCAS WILL ONLY SENSE TRAFFIC BEHIND THE AIRCRAFT.
(1)
Remove the used sealant from the fuselage structure (2) with a nonmetallic scraper.
(2)
Clean the component interface and/or the adjacent area with CLEANING AGENTS (Material No. 11-004) and a lint-free cloth.
NOTE : If you install the same antenna it is necessary to clean it
____ with CLEANING AGENTS (Material No. 11-003).
(3)
Do an inspection of the component interface and/or the adjacent area.
(4)
Put the new O-ring (4) in the correct position on the antenna (6).
(5)
FOR 7SG1
Install the foam washer (5).
(6)
Align the new gasket (3) on the fuselage with the screw holes.
(7)
Remove the blanking caps from the coaxial connectors (1) and (9).
1EFF : ALL 1 34-43-11Page 412 1 1 Aug 01/05 1 1 1CES 1
(8)
Make sure that the electrical connectors are clean end in the correct
condition.
(9)
Remove the masking tape from the coaxial cables and connect each
connector (1) to the related connector (9) (see color code).
NOTE : You must connect the connector J1 (YELLOW) to the front.
____
(10)
Safety the coaxial connectors (1) and (9) with corrosion-resistant steel lockwire 0.4 mm (0.016 in.) dia..
(11)
Install the antenna (6) on the fuselage structure (2) with the screws
(7) and the washers (8) and then tighten:
-TORQUE the screws to between 0.27 and 0.37 m.daN (23.89 and 32.74 lbf.in)
(12)
Make sure that the bonding contact resistance between the antenna (6) and the fuselage structure (2) is not higher than 5 milliohms (Ref. TASK 20-28-00-912-005).
(13)
Install the MISCELLANEOUS (Material No. 19-002) (10) on the screw heads with the SEALANTS (Material No. 09-016) . This is necessary for the subsequent removal of the antenna. (see detail on section B-B).
(14)
Put a bead of SEALANTS (Material No. 09-016) around the antenna (6).
(15)
Let the sealant become dry.
(16)
Apply STRUCTURE PAINTS (Material No. 16-003) to the sealant around the antenna and the screw heads.
(17)
Apply PAINTS FOR DETAIL (INTERNAL AND EXTERN AL) (Material No. 07-001B) to the sealant of the head of the screws (7).
R 1EFF : 001-049, 101-105, 151-199, 1 34-43-11Page 413 1 1 May 01/05 1 1 1CES 1
R **ON A/C 051-099,
R Subtask 34-43-11-420-050-B
R A. Installation of the TCAS Antenna
R (Ref. Fig. 401A/TASK 34-43-11-991-001-B)
R WARNING : OBEY THE COLOR CODES WHEN YOU CONNECT THE ELECTRICAL CONNECTORS_______
R (THIS WILL PREVENT CROSS-CONNECTIONS).
R MAKE SURE THAT YOU INSTALL THE ANTENNA IN THE CORRECT
R DIRECTION. IF THE ANTENNA DOES NOT POINT IN THE CORRECT
R DIRECTION, THE TCAS WILL ONLY SENSE TRAFFIC BEHIND THE
R AIRCRAFT.
R (1) Remove the used sealant from the fuselage structure (1) with a
R nonmetallic scraper.
R (2) Clean the component interface and/or the adjacent area with CLEANING
R AGENTS (Material No. 11-004) and a lint-free cloth.
R NOTE : If you install the same antenna it is necessary to clean it____
R with CLEANING AGENTS (Material No. 11-003).
R (3) Do an inspection of the component interface and/or the adjacent area.
R (4) Put the new O-ring (4) in the correct position on the antenna (6).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM NAVIGATION 导航3(146)
