(7)
Install the PIN - RIGGING (98D27207545000) or RIGGING PIN SET (98D27207516000) (35) on the left input lever of the travel limitation unit (27). You must install and remove the rigging pin (35) easily. If not, do these operations :
(a)
Remove and discard the cotter pins (38).
(b)
Loosen the nuts (37).
(c)
Remove the retainers (36).
(d)
Cut and remove the lockwire from the nuts of the rod (26).
(e)
Loosen the nuts.
(f)
Release the lockwashers.
1EFF : ALL 1 27-21-00Page 522 1 1 May 01/05R 1 1 1CES 1
(g)
Adjust the length of the rod (26) until you can install and remove the rigging pin (35) freely.
(h)
Engage the lockwashers.
(i)
Tighten the nuts.
(j)
Make sure that the adjustment is correct after you have tightened the nuts.
(k)
Safety the nuts with MISCELLANEOUS (Material No. 19-010).
(l)
Put the rod retainers (36) in position. Tighten the nuts (37). Install the new cotter pins (38).
(8) Install the PIN - RIGGING (98D27207545000) or RIGGING PIN SET (98D27207516000) (29) on the output bellcrank of the centering spring rod (15). You must install and remove the rigging pin (29) easily. If not, do these operations :
(a)
Remove and discard the cotter pins (38).
(b)
Loosen the nuts (37).
(c)
Remove the retainers (36).
(d)
Cut and remove the lockwire from the nuts of the rod (28).
(e)
Loosen the nuts.
(f)
Release the lockwashers.
(g)
Adjust the length of the rod (28) until you can install and remove the rigging pin (29) freely.
(h)
Engage the lockwashers.
(i)
Tighten the nuts.
(j)
Make sure that the adjustment is correct after you have tightened the nuts.
(k)
Safety the nuts with MISCELLANEOUS (Material No. 19-010).
(l)
Put the rod retainers (36) in position. Tighten the nuts (37). Install the new cotter pins (38).
1EFF : ALL 1 27-21-00Page 523 1 1 May 01/05R 1 1 1CES 1
(9) Install the PIN - RIGGING (98D27207545000) or RIGGING PIN SET (98D27207516000) (34) on the right input lever of the travel limitation unit (27). You must install and remove the rigging pin (34) easily. If not, do these operations :
(a)
Cut and remove the lockwire from the nuts of the rod (16).
(b)
Loosen the nuts.
(c)
Release the lockwashers.
(d)
Adjust the length of the rod (16) until you can install and remove the rigging pin (34) freely.
(e)
Engage the lockwashers.
(f)
Tighten the nuts.
(g)
Make sure that the adjustment is correct after you have tightened the nuts.
(h)
Safety the nuts with MISCELLANEOUS (Material No. 19-010).
(10) Disconnect the centering spring rod (15) as follows:
(a)
Remove the cotter pin (30) and discard it.
(b)
Remove the nut (31) and the washer (32).
(c)
Remove the bolt (33) and disconnect the centering spring rod (15).
Subtask 27-21-00-820-059
D. Adjustment of the Rudder Neutral Position
(1) Adjust the rudder neutral position (Ref. TASK 27-24-00-820-001).
1EFF : ALL 1 27-21-00Page 524 1 1 May 01/05R 1 1 1CES 1
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 27-21-00-710-054
E. Test
(Ref. Fig. 505/TASK 27-21-00-991-003)
(Ref. Fig. 502/TASK 27-21-00-991-004)
(Ref. Fig. 503/TASK 27-21-00-991-005)
(Ref. Fig. 504/TASK 27-21-00-991-012)
(1) Preparation for the Test.
(a) Remove the three rigging pins (1): 1 From the connection relay of the CAPT rudder pedals (10).
_
2 From the connection relay of the F/O rudder pedals (2).
_
3 From the tension regulator (7).
_
(b)
Remove the rigging pin (42) from the cable quadrant (24).
(c)
Remove the rigging pin (39) from the output bellcrank of the servocontrol (21).
(d)
Remove the rigging pins (34) and (35) from the input levers of the travel limitation unit (27).
(e)
Remove the rigging pin (40) from the mixer (41) of the artificial feel unit.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵1(143)
