R 1EFF : 001-003, 051-052, 1 27-14-51Page 426 1 1 May 01/05 1 1 1CES 1
(3)
For 33CE1(33CE2), install the ASC (21):
(a)
Hold the ASC (7.4 kg (16.3142 lb)) in a horizontal position.
(b)
Align the body eye-end with the bushes in the flanges of the rear-spar jack-bracket.
(c)
Install the pin (19).
(d)
Manually move the aileron to the down position. Do this until the piston-rod eye-end and the bushes of the aileron jack-bracket are aligned.
(e)
Install the pin (23).
(4)
For 33CE3(33CE4), install the ASC (20):
(a)
Hold the ASC (7.4 kg (16.3142 lb)) in a horizontal position.
(b)
Align the body eye-end with the bushes in the flanges of the rear-spar jack-bracket.
(c)
Install the pin (18).
(d)
Manually move the aileron to the down position. Do this until the piston-rod eye-end and the bushes of the aileron jack-bracket are aligned.
(e)
Install the pin (22).
(5)
For easier access to the installed ASC manually, put and hold the aileron in the fully-up position.
(6)
Apply COMMON GREASE (Material No. 04-022) to the threads of the pins:
-
for 33CE1(33CE2), the pins (19) and (23)
-
for 33CE3(33CE4), the pins (18) and (22).
If the aileron servo control is safetied with ABS 0738 nuts, do the steps that follow:
(7) Install the flanged bushes (8) and (10) into the inboard-flanges of the aileron and rear-spar jack-brackets.
R 1EFF : 001-003, 051-052, 1 27-14-51Page 427 1 1 May 01/05 1 1 1CES 1
(8) Apply a layer of STORAGE PRESERVATION (Material No. 15-007) to the eye-ends of the piston rods on the rounded sides only.
NOTE : Do not get Material 15-007 on the Servocontrol Spherical
____
Bearings.
(9) For 33CE1(33CE2), install the ASC (25):
(a)
Hold the ASC (7.4 kg (16.3142 lb)) in a horizontal position.
(b)
Align the body eye-end with the bushes in the flanges of the rear-spar jack-bracket.
(c)
Install the pin (23).
(d)
Manually move the aileron to the down position. Do this until the piston-rod eye-end and the bushes of the aileron jack-bracket are aligned.
(e)
Install the pin (27).
(10)
For 33CE3(33CE4), install the ASC (24):
(a)
Hold the ASC (7.4 kg (16.3142 lb)) in a horizontal position.
(b)
Align the body eye-end with the bushes in the flanges of the rear-spar jack-bracket.
(c)
Install the pin (22).
(d)
Manually move the aileron to the down position. Do this until the piston-rod eye-end and the bushes of the aileron jack-bracket are aligned.
(e)
Install the pin (26).
(11)
For easier access to the installed ASC manually, put and hold the aileron in the fully-up position.
(12)
Apply COMMON GREASE (Material No. 04-022) to the threads of the pins:
-
for 33CE1(33CE2), the pins (23) and (27)
-
for 33CE3(33CE4), the pins (22) and (26).
Subtask 27-14-51-420-058 R C. Complete the Installation of the Aileron Servo Control (ASC)
If the aileron servo control is safetied with STA-LOK nuts, do the steps that follow:
(1)
Install the STA-LOK nuts (5) and (14) and the STA-LOK washers (4) and
(13)
as follows (Ref. TASK 20-22-00-400-001):
(a)
Install the STA-LOK nuts (5) and (14) with the WRENCHES -NOTCHED, TIGHTENING OF NUTS NSA5454 (SL90-315-7500).
(b)
TORQUE the nuts (5) and (14) to between 7.0 and 8.0 m.daN (51.62 and 58.99 lbf.ft).
(c)
Install the STA-LOK washers (4) and (13) with the TOOL -INSTALLATION, TAB WASHERS STA-LOK NSA5454 (SL90-313-7500).
(2)
For 33CE1(33CE2), do the steps that follow:
(a)
At the rear-spar jack-bracket: (Ref. Fig. 401/TASK 27-14-51-991-001)
(b)
At the aileron jack-bracket: 1 Put the locking plate (22) on the pin (23).
1_ Put the locking plate (18) on the pin (19).
2_ Align the bolt hole in the locking plate (18) with the holes
in the flanges of the rear-spar jack-bracket.
3_ Install the bolt (17), the washer (16) and the nut (15).
_ 2 Align the bolt hole in the locking plate (22) with the hole in 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵1(111)
