Aileron Servo Control
Figure 601/TASK 27-14-51-991-003- 12 (SHEET 1)
R 1EFF : 001-003, 051-052, 1 27-14-51Page 604 1 1 May 01/05 1 1 1CES 1
Aileron Servo Control
Figure 601/TASK 27-14-51-991-003- 22 (SHEET 2)
R 1EFF : 001-003, 051-052, 1 27-14-51Page 605 1 1 May 01/05 1 1 1CES 1
Aileron Servo Control Figure 601A/TASK 27-14-51-991-003-A
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 27-14-51Page 606 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | View B | 22.184 | 22.205 | | | 22.160 | | | | OD 4 |(0.8733) |(0.8742) | | |(0.8724) | | | | | | | 0.007 | 0.041 | | | 0.089 | | | | | (0.0002)| (0.0016)| | |(0.0035)| | View B | 22.212 | 22.225 | | | | 22.249 | | | ID 2 |(0.8744) |(0.8750) | | | |(0.8759) | | -------------------------------------------------------------------------------
Subtask 27-14-51-220-052
C. Fits and Clearances
(1) Complete an inspection of these dimensions.
-------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | View B | 22.184 | 22.205 | | | 22.143 | | | | OD 4 |(0.8733) |(0.8742) | | |(0.8717) | | | | | | | 0.020 | 0.062 | | | 0.144 | | | | | (0.0007)| (0.0024)| | |(0.0056)| | View B | 22.225 | 22.246 | | | | 22.287 | | | ID 3 |(0.8750) |(0.8758) | | | |(0.8774) | | -------------------------------------------------------------------------------
Subtask 27-14-51-220-053
D. Fits and Clearances
(1) Complete an inspection of these dimensions.
-------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | View B | 26.968 | 26.981 | | | 26.946 | | | | OD 5 |(1.0617) |(1.0622) | | |(1.0608) | | | | | | | 0.006 | 0.041 | | | 0.087 | | | | | (0.0002)| (0.0016)| | |(0.0034)| | View B | 26.987 | 27.009 | | | | 27.033 | | | ID 1 |(1.0624) |(1.0633) | | | |(1.0642) | | -------------------------------------------------------------------------------
Subtask 27-14-51-020-063
E. Replacement of Unserviceable Items
(1) If you find unserviceable items, replace the applicable item(s) as follows:
(a) For View B:
-
install a new bush (3)
-
install a new flanged bush (4).
5. Close-up
________
Subtask 27-14-51-410-055
A. Close Access
(1)
Install the aileron servo control (Ref. TASK 27-14-51-400-001).
(2)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
Subtask 27-14-51-942-064
B. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
RUDDER - DESCRIPTION AND OPERATION
__________________________________
1. General_______ (Ref. Fig. 001) One rudder surface provides the yaw control. The main control is mechanical (Ref. 27-21). The trim control is electrically signalled (Ref. 27-22). The artificial feel (Ref. 27-23) is ensured by:
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵1(133)
