NOTE : If the screw holes in the flange and the lockplate (8) are not
____ aligned, increase the torque by small increments. Continue to tighten the eye-end until the screw holes are aligned. Do not exceed 7 m.daN (51.6 lbf.ft).
(6)
TORQUE the screws (1) to between 0.21 and 0.26 m.daN (18.58 and 23.00 lbf.in).
(7)
Safety the screws (1) with MISCELLANEOUS (Material No. 19-010).
5. Close-up
________ Subtask 27-14-51-420-057
A. Installation of the Aileron Servo-Control Block
(1) Install the Aileron Servo-Control Block (Ref. TASK 27-14-51-400-001). Subtask 27-14-51-942-065
B. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
SERVO CONTROL - AILERON (33CE1,33CE2,33CE3,33CE4) - INSPECTION/CHECK____________________________________________________________________
TASK 27-14-51-200-001
Check of the Aileron Servo Control
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED DOORS - COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:_______ - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS. - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS. - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job__________________
Self Explanatory
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific No specific safety barrierswarning notice
R B. Expendable Parts
R R R -------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
R R 3 4 bush flanged bush 27-14-05 21 -150 27-14-05 21 -150
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-14-51-000-001 Removal of the Aileron Servo Control
27-14-51-400-001 Installation of the Aileron Servo Control
**ON A/C 001-003, 051-052,
27-14-51-991-003 Fig. 601 R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
27-14-51-991-003-A Fig. 601A
**ON A/C ALL
3. Job Set-up
__________
Subtask 27-14-51-941-072
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put a warning notice in position to tell persons not to operate the flight controls.
Subtask 27-14-51-010-055
B. Get Access
(1) Remove the aileron servo control (Ref. TASK 27-14-51-000-001).
4. Procedure
_________
**ON A/C 001-003, 051-052,
(Ref. Fig. 601/TASK 27-14-51-991-003)R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(Ref. Fig. 601A/TASK 27-14-51-991-003-A)
**ON A/C ALL
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 27-14-51-220-050
A. Fits and Clearances
(1) Complete an inspection of these dimensions.
-------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | View B | 22.184 | 22.205 | | | 22.143 | | | | OD 4 |(0.8733) |(0.8742) | | |(0.8717) | | | | | | | 0.020 | 0.062 | | | 0.144 | | | | | (0.0007)| (0.0024)| | |(0.0056)| | View B | 22.225 | 22.246 | | | | 22.287 | | | ID 5 |(0.8750) |(0.8758) | | | |(0.8774) | | -------------------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵1(132)
