(3)
Put the LVDT (6) in position on the aileron servo-control. NOTE : You must compress the spring in the aileron servo-control to
____
do this.
(4)
Install the bonding leads (5), the lockwasher (4), the washers (2) and the bolts (3).
(5)
TORQUE the bolts (3) to between 0.46 and 0.54 m.daN (40.70 and 47.78 lbf.in).
(6)
Do a bonding check on the LVDT (6) (Ref. TASK 20-28-00-912-004).
(7) Safety the bolts (3) with MISCELLANEOUS (Material No. 19-010). Subtask 27-14-51-860-067
C. Aircraft Maintenance Configuration
(1)
Connect the Isolation Coupling of the Power Transfer Unit (PTU) (Ref. TASK 29-23-00-860-002).
(2)
Remove the container from under the LVDT (6).
(3)
Make sure that the work area is clean and clear of tool(s) and other items.
Subtask 27-14-51-865-064
D. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 15CE1, 15CE2, 16CE1, 16CE2.
Subtask 27-14-51-710-054
E. Test
(1)
Do a check of the aileron adjustment (Ref. TASK 27-14-00-820-001).
(2)
Do a operational test of the aileron (Ref. TASK 27-14-00-710-001).
(3)
Examine the LVDT (6) for leaks.
5. Close-up
________
**ON A/C 001-003, 051-052,
(Ref. Fig. 406/TASK 27-14-51-991-007) R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(Ref. Fig. 406A/TASK 27-14-51-991-007-A)
**ON A/C ALL
Subtask 27-14-51-410-054
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the applicable access panel:
-for the left wing, panel 575AT
-for the right wing, panel 675AT.
Subtask 27-14-51-942-060
B. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
TASK 27-14-51-000-006
Removal of the Actuator Eye-End of the Aileron Servo-Control
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice 0U144765 1 WRENCH - AILERON SERVOCONTROL ADJUSTMENT 0U144768 1 HOLDING WRENCH - AILERON SERVOCONTROL ADJUSTMENT
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-14-51-000-001 Removal of the Aileron Servo Control 27-14-51-991-008 Fig. 407
3. Job Set-up
__________ Subtask 27-14-51-941-073
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put a warning notice in position to tell persons not to operate the flight controls.
Subtask 27-14-51-020-055
B. Removal of the Aileron Servo-Control Block
(1)
Remove the aileron servo-control block (Ref. TASK 27-14-51-000-001).
(2)
Take the servo-control block to a workshop bench and clamp it so that you can do work on the eye-end.
4. Procedure_________ (Ref. Fig. 407/TASK 27-14-51-991-008) CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵1(129)
