(c)
Make sure that this circuit breaker is open and has safety tag:
EFFECTIVITY SIL ALL 34-24 TASK 815
D633A103-SIL BOEING PROPRIETARY -Copyright # Unpublished Work -See title page for details Page 216 Jun 15/2010
CAPT Electrical System Panel, P18-2
Row Col Number Name
D 8 C01551 ISFD
(d) Do a wiring check between the pins of these connectors (WDM 34-24-15):
D11281 D41807P
pin6 -------------------pin29
(e)
Repair the problems that you find and continue.
(f)
Re-install the ISFD dedicated battery system, M2100. To install it, do this task: ISFD Dedicated Battery System and Battery Pack Installation, AMM TASK 34-24-03-400-801.
(g)
Connect the connector D41807P to the P18-2 panel.
(h)
Remove the safety tag and close this circuit breaker:
CAPT Electrical System Panel, P18-2
Row Col Number Name
D 8 C01551 ISFD
(i) If the test in the installation task for the ISFD dedicated battery system is satisfactory and the FAULT light on the face of the IFSD dedicated battery system is not on, then you corrected the fault.
-------------------------END OF TASK ---------------------------
EFFECTIVITY SIL ALL 34-24 TASK 815
D633A103-SIL BOEING PROPRIETARY -Copyright # Unpublished Work -See title page for details Page 217 Jun 15/2008
801. ILS or Multi-Mode Receiver BITE Procedure
A. General
(1)
You do the multi-mode receiver (MMR) BITE test at the front panel of the MMR.
(2)
There are two multi-mode receivers (MMR). MMR 1 is on the E1-2 shelf and MMR 2 is on the E1-4 shelf in the electronic equipment compartment.
SIL 001-003; AIRPLANES WITH BENDIX (ALLIED SIGNAL) MULTI-MODE RECEIVERS
(3) The MMR BITE test does a self check for existing internal and external faults. Results of the BITE test are displayed on the LCD screen on the front panel of the MMR.
SIL 004-021, 101-999; AIRPLANES WITH COLLINS OR SEXTON RECEIVERS
(4) The MMR BITE test does a self check for existing internal and external faults. Results of the BITE test are displayed on the front panel of the MMR.
SIL 001-003
(5) The MMR flight fault memory stores fault data that occurs in flight. You can view faults that occurred on previous flight legs to help isolate an intermittent fault that is not found by the BITE self-test.
SIL 004-021, 101-999
(6) The Collins multi-mode receivers have 3 indicating lights on the front panel. However, the ANTENNA FAIL light is not used and it will stay off at all time.
NOTE: On airplanes with Collins SB GLU-920-34-15, the ANTENNA FAIL light will come on but this does not indicate a failure.
SIL 007, 008, 013-016, 019-021, 101-999
NOTE: On airplanes with GLS capabilities, the ANTENNA FAIL light on the Collins MMR may indicate GPS antenna/connection failure.
SIL ALL
B. BITE Procedure
(1) Do the BITE procedure for the MMR.
SIL 004-021, 101-999; AIRPLANES WITH COLLINS MULTI-MODE RECEIVERS
(2) Push and release the TEST switch on the front panel of the receiver to start the BITE test.
(a)
Make sure that these indications occur: 1) All the red lights come on. 2) The LRU STATUS light changes to green after 2 seconds. 3) All the lights go off after 2 seconds. 4) The green LRU STATUS light comes on after 30 seconds.
(b)
Refer to the table at the end of this task to find the fault isolation task for the applicable maintenance messages.
SIL 001-003; AIRPLANES WITH BENDIX (ALLIED SIGNAL) MULTI-MODE RECEIVERS
(3) Push and release either of the two switches on the front panel of the receiver to start the BITE test.
(a)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-600/700/800/900 FAULT ISOLATION MANUAL 故障隔离手册 导航(91)
