(b) If the fault continues:
- do a visual inspection of the P25 probe (Ref. AMM TASK 73-21-80-210-002).
B. Do the test given in Para. 3.A.
(1) No additional maintenance action is required if the fault is not confirmed.
(2) Repeat the fault isolation procedure if the fault continues.
F 『 EEFF : ALL E ∞∞73-20-00∞∞∞∞∞∞∞∞∞∞Page A281
E E Aug 01/05 ERE
ECES E 56 E
F 『
E C F M E
E E
E E TASK 73-20-00-810-956
Loss of all Engine 2 Indication Plug Data
1. Possible Causes
_______________
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with Engine non Motoring)
3. Fault Confirmation
__________________
A. Do the operational test of the FADEC 2B on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
4. Fault Isolation
_______________
A. Do the test given in Para. 3.A.
F 『 EEFF : ALL E ∞∞73-20-00∞∞∞∞∞∞∞∞∞∞Page A282
E E Aug 01/05 ERE
ECES TASK 73-20-00-810-957
F 『
E C F M E
E E
E 56 E
E E
Loss of all Engine 1 Identification Connector Data
1. Possible Causes
_______________
- J14 engine identification connector
- ECU1 (4000KS)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU) AMM 73-21-60-400-001 Installation of the Electronic Control Unit (ECU) AMM 73-21-60-740-006 Read the LRU Identification Report and the Thrust
Reverser Shut-off Valve Status AMM 73-21-90-000-002 Removal of the Engine Identification Connector AMM 73-21-90-400-002 Installation of the Engine Identification Connector AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with
Engine non Motoring)
3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the FADEC 1B on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
(2) Do the LRU identification through the MCDU (Ref. AMM TASK 73-21-60-740-006) and check that the data corresponds to the engine configuration.
4. Fault Isolation
_______________
A. If the test gives the maintenance message J14, ECU (ENG IDENT):
- do a check for the loose or missing identification connector at the ECU1 connector J14 receptacle.
(1) If the Service Bulletin 72-0340 is not incorporated, and if the fault continues:
- reset the ECU1 (4000KS) as follows:
(a) On the panel 115VU, set the ENG/MASTER 1 control switch (3KC) to OFF.
F 『 EEFF : ALL E ∞∞73-20-00∞∞∞∞∞∞∞∞∞∞Page A283
E E Aug 01/05 ERE
ECES E 56 E E E
F 『
E C F M E
E E
(b) After 30 seconds, set the ENG/MASTER 1 control switch (3KC) to ON.
1 If the fault continues:
_
- replace the J14 engine identification connector (Ref. AMM TASK 73-21-90-000-002) and (Ref. AMM TASK 73-21-90-400-002).
a If the fault continues:
_
- replace the ECU1 (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
(2) If the Service Bulletin 72-0340 is incorporated, and if the fault continues:
- read the LRU IDENTIFICATION report of the engine 1 (Ref. AMM TASK 73-21-60-740-006),
- check that the engine identification connector installed on the engine meets the specific engine configuration (rating, N1 trim, system configuration, etc...).
(a) If the rating identified on the LRU IDENTIFICATION report is incorrect:
- replace the J14 engine identification connector (Ref. AMM TASK 73-21-90-000-002) and (Ref. AMM TASK 73-21-90-400-002).
(b) If other parameters than the rating identified on the LRU IDENTIFICATION report is (are) incorrect:
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 发动机燃油和控制 1(136)
