A. If the test of the channel A gives the maintenance message T25 SNSR, J12, ECU*:
- do a check for open or short to ground of the harness J11 between the ECU (4000KS) and the 6 o'clock junction box, between the 6 o'clock junction box and the T25 temperature sensor pins J11/19, 37, 38 to pins J11/1, 2, 3 (Ref. ASM 73-25/18).
(1) If the wiring is not correct:
- repair the above wiring.
(2) If the wiring is correct: R - disconnect the harness J11 from the ECU (4000KS). R - do a visual inspection of the harness connector and receptacle. R Look for contamination or oxidation or pins that have damage. R - if you find damage, repair or replace as required. R - clean the connector and receptacle with a bristle brush and R stoddard solvent (Material No. CP2011) (Ref. AMM TASK 73-21-50-210-R 002). R - do a check of the ECU cable resistance between: R
. pins 37 and 38 (160 to 250 Ohms) . pins 37 and 19 (> 10 Megohms) . pin 37 and the ground (> 10 Megohms).
(a) If the resistance values are in the specified limits:
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
(b) If the resistance values are out of the specified limits: R - disconnect the harness CJ11 at the 6 o'clock junction box. R - do a visual inspection of the harness connector and receptacle. R Look for contamination or oxidation or pins that have damage. R - if you find damage, repair or replace as required. R - clean the connector and receptacle with a bristle brush and R stoddard solvent (Material No. CP2011) (Ref. AMM TASK 73-21-50-R 210-002). R - do a check of the resistance of the cable CJ11R between: R
. pins 25 and 26 (160 to 250 Ohms) . pins 25 and 13 (> 10 Megohms) . pin 25 and the ground (> 10 Megohms).
F 『 EEFF : ALL E ∞∞73-20-00∞∞∞∞∞∞∞∞∞∞Page 293
E E Aug 01/05 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
1 If the resistance values are in the specified limits:
_
- replace the harness J11 (Ref. AMM TASK 73-21-50-000-044) and (Ref. AMM TASK 73-21-50-400-044).
2 If the resistance values are out of the specified limits:
_ R - disconnect the harness CJ11R at the T25 temperature sensor. R - do a visual inspection of the harness connector and R receptacle. Look for contamination or oxidation or pins that R have damage. R - if you find damage, repair or replace as required. R - clean the connector and receptacle with a bristle brush and R stoddard solvent (Material No. CP2011) (Ref. AMM TASK 73-21-R 50-210-002). R - do a check of the T25 sensor resistance between: R
. pins 1 and 2 (160 to 250 Ohms) . pin 1 and the ground (> 10 Megohms).
a If the resistance values are in the specified limits:
_
- replace the harness CJ11R (Ref. AMM TASK 73-21-50-000-026) and (Ref. AMM TASK 73-21-50-400-026).
b If the resistance values are out of the specified limits:
_
- replace the T25 temperature sensor (Ref. AMM TASK 73-21-20-000-002) and (Ref. AMM TASK 73-21-20-400-002).
B. Do the test given in Para. 3.A.
F 『 EEFF : ALL E ∞∞73-20-00∞∞∞∞∞∞∞∞∞∞Page 294
E E Aug 01/05 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
TASK 73-20-00-810-899
Failure of the High Pressure Shut Off Valve Switch of the HMU on Engine 1
1. Possible Causes
_______________
- hydromechanical unit (HMU)
- harness J7
- harness J8
- ECU (4000KS)
2. Job Set-up Information
______________________
R A. Fixtures, Tools, Test and Support Equipment
R -------------------------------------------------------------------------------R REFERENCE QTY DESIGNATION
R -------------------------------------------------------------------------------
R No specific bristle brush
R B. Consumable Materials
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R Material No. CP2011 *
R stoddard solvent (Ref. 70-30-00)
R C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
R AMM AMM AMM AMM AMM AMM AMM AMM AMM AMM 71-00-00-710-002 73-21-10-000-002 73-21-10-400-002 73-21-50-000-040 73-21-50-000-041 73-21-50-210-002 73-21-50-400-040 73-21-50-400-041 73-21-60-000-001 73-21-60-400-001
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 发动机燃油和控制 1(102)
