F 『
E C F M E
E E
E 56-5B E
E E
HYDRO-MECHANICAL UNIT (HMU) - SERVICING
_______________________________________ TASK 73-21-10-600-002 Preservation of the Hydromechanical Unit (HMU)
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP2442 * engine oil (Ref. 70-30-00)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
73-21-10-991-300 Fig. 301
3. Job Set-up
__________ Subtask 73-21-10-869-052
A. Not Applicable
4. Procedure
_________ (Ref. Fig. 301/TASK 73-21-10-991-300) Subtask 73-21-10-020-054
A. Preparation for removal: CAUTION : DO NOT HOLD OR MOVE THE HYDROMECHANICAL UNIT BY THE TORQUE
_______ MOTORS. CHANGES TO THE CALIBRATION OF THE HYDROMECHANICAL UNIT CAN OCCUR.
F 『 EEFF : ALL E Page 30173-21-10
E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E
Hydromechanical Unit
Figure 301/TASK 73-21-10-991-300- 12 (SHEET 1)
F EEFF : ALL 『E 73-21-10 Page 302
E E Feb 01/98
E E
ECES E
Hydromechanical Unit
Figure 301/TASK 73-21-10-991-300- 22 (SHEET 2)
F EEFF : ALL 『E 73-21-10 Page 303
E E Feb 01/98
E E
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(1) Remove the following from the new HMU and keep the gaskets:
(a) Screws (90) and shipping cover (80).
(b) Gasket (70, 100, 130).
(c) Screws (120) and shipping cover (110).
(d) Screws (150) and shipping cover (140).
(e) Shipping plugs (10, 20, 60, 190, 210, 30, 50, 170, 200, 40, 180).
(f) Shipping caps (220, 160).
(2) Remove the nut (250) and the washer (240) from the HMU studs.
(3) Remove the nuts (260) and the washers (270). Then, remove the bolt
(300) and the washer (290).
Subtask 73-21-10-550-052
B. Remove the new HMU from the shipping block (280). Keep the gasket (230). Subtask 73-21-10-680-052
C. Fully drain the fuel from the old HMU.
Subtask 73-21-10-620-053
D. Put 1 l (0.25 USgal) of engine oil (Material No. CP2442) into the PCR port of the old HMU.
Subtask 73-21-10-420-055
E. Install the shipping plug (200) in the PCR port.
Subtask 73-21-10-620-054
F. Carefully turn the HMU a minimum of one turn to apply engine oil
(Material No. CP2442) to the internal parts.
Subtask 73-21-10-020-055
G. Remove the shipping plug (200) from the PCR port.
F 『 EEFF : ALL E Page 30473-21-10
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E E E Subtask 73-21-10-680-053
H. Fully drain the engine oil (Material No. CP2442) from the PCR port. Subtask 73-21-10-420-056
J. Preparation for installation:
(1) Install the shipping plugs, caps, covers and gaskets to the old HMU as follows:
(a) Gasket (70), shipping cover (80), and screws (90).
(b) Gasket (100), shipping cover (110), and screws (120).
(c) Gasket (130), shipping cover (140), and screws (150).
(d) Shipping plugs (10, 20, 60, 190, 210, 30, 50, 170, 200, 40, 180).
(e) Shipping cap (160, 220).
(2) Install gasket (230) on the shipping block (280). Align the holes in the gasket (230) with the holes in the shipping block (280).
Subtask 73-21-10-550-053
K. Install the old HMU on the gasket (230) and shipping block (280). Subtask 73-21-10-420-057
L. Safety the HMU on the shipping block:
(1) Install the washers (240) and nuts (250) on the HMU studs.
(2) Install the bolts (300) and washers (290) through the HMU flange and shipping block (280). 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM 发动机燃油和控制 ENGINE FUEL AND CONTRO(101)
