F 『 EEFF : ALL E Page 45372-63-00
E E May 01/05 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
- forward sump drain tube (Ref. TASK 71-73-49-400-029)
(13) Install the drain manifold module (Ref. TASK 71-71-43-400-041).
(14) Install the fan fire detector (Ref. TASK 26-12-15-400-042). Subtask 72-63-00-410-068
E. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Close the thrust reverser doors: (Ref. TASK 78-36-00-410-040) FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR
(3) Remove the warning notice(s). Subtask 72-63-00-440-051
F. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041) Subtask 72-63-00-710-056
G. Test after the Installation
(1) Do a minimum idle check (Ref. TASK 71-00-00-710-006) and a check for leaks (Ref. TASK 79-00-00-210-003).
(2) Do a check of the oil level (Ref. TASK 12-13-79-610-002) or (Ref. TASK 12-13-79-610-002).
(3) Do an accel check (Ref. TASK 71-00-00-710-025).
F 『 EEFF : ALL E Page 45472-63-00
E E May 01/05 ERE
ECES E 5. Close-up
F 『
E C F M E
E E
E 56-5B E
E E
________ Subtask 72-63-00-410-069
A. Close Access
(1) Close the fan cowl doors: (Ref. TASK 71-13-00-410-040) FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
(2) Remove the access platform(s).
F 『 EEFF : ALL E Page 45572-63-00
E E May 01/05 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
ACCESSORY GEARBOX ASSEMBLY - INSPECTION/CHECK
_____________________________________________ TASK 72-63-00-210-002 Inspection/Check of the Accessory Gearbox Assembly
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP8001 * lockwire 0.032 in. (0.8 mm) dia. (Ref. 70-30-00) Material No. CP8002 * lockwire 0.032 in. (0.8 mm) dia. (Ref. 70-30-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 71-13-00-410-040 Closing of the Fan Cowl Doors 72-63-00-300-002 Replacement of a Sealol Seal (Typical) 72-63-00-300-003 Replacement of a Magnetic Seal (Typical)
F 『 EEFF : ALL E Page 60172-63-00
E E Feb 01/98 E E ECES E 3. Job Set-up
F 『
E C F M E
E E
E 56-5B E
E E
__________ Subtask 72-63-00-941-057
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a warning notice to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a warning notice to tell persons not to energize the FADEC 1(2).
Subtask 72-63-00-010-064
B. Open the fan cowl doors: (Ref. TASK 71-13-00-010-040)
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
4. Procedure
_________ Subtask 72-63-00-210-052
A. Inspection of the AGB external areas.
-------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
1. Housing for :
A. Cracks Not serviceable
B. Nicks, dents and Any number, 0.035 in.
scratches (0.9 mm) deep after
removal of high metal.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM ENGINE 发动机 2(146)
