(3) Install the Electric Master Chip Detector (Ref. TASK 79-00-00-281-002).
5. Close-up
________
Subtask 79-35-00-410-053
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Close the fan cowl doors: (Ref. TASK 71-13-00-410-040) FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
(3) Remove the warning notice(s). R
R (4) Make an entry in the log book.
R Subtask 79-35-00-862-051
R B. De-energize the ground service network (Ref. TASK 24-42-00-862-001).
F 『 EEFF : ALL E Page 40779-35-00
E E May 01/03 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
SWITCH - OIL FILTER DIFFERENTIAL PRESSURE (4001EN) - REMOVAL/INSTALLATION
_________________________________________________________________________ TASK 79-35-15-000-003 Removal of the Oil Filter Differential Pressure Switch
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking plugs and caps No specific container 1l (0.25 USgal) No specific soft-nose connector pliers No specific warning notice
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 79-35-15-991-300 Fig. 401
3. Job Set-up
__________ Subtask 79-35-15-941-050
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a warning notice to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
F 『 EEFF : ALL E Page 40179-35-15
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a warning notice to tell persons not to energize the FADEC 1(2).
Subtask 79-35-15-010-050
B. Open the fan cowl doors: (Ref. TASK 71-13-00-010-040)
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
4. Procedure
_________
(Ref. Fig. 401/TASK 79-35-15-991-300)
Subtask 79-35-15-020-050
A. Removal of the Differential Pressure Switch
(1) Disconnect the HJ7 harness connector (10) from the differential pressure switch (20). Use soft-nose connector pliers only if necessary.
(2) Remove the bolts (50) which attach the differential pressure switch
(20) to the lubrication unit.
(3) Put a container 1l (0.25 USgal) below the differential pressure switch.
(4) Remove the differential pressure switch (20) from the lubrication unit.
(5) Remove and discard the O-rings (30) and (40).
(6) Put blanking plugs and caps on the disconnected parts and orifice.
F 『 EEFF : ALL E Page 40279-35-15
E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E
Oil Filter Differential-Pressure-Switch
Figure 401/TASK 79-35-15-991-300
F EEFF : ALL 『E 79-35-15 Page 403
E E Feb 01/98
E E
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
TASK 79-35-15-400-003
Installation of the Oil Filter Differential Pressure Switch
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific soft-nose connector pliers
No specific warning notice
No specific Torque Wrench : range 35 to 45 lbf.in
(0.39 to 0.50 m.daN)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM OIL 滑油(78)
