(5) Connect the connector (80) to the 90 degrees interface connector (Item 2).
(a) Fully tighten the connector (80) by hand. Subtask 79-21-50-790-050
B. Do a minimum idle check for a minimum of 3 minutes and check for leaks (Ref. TASK 71-00-00-710-006) (Ref. TASK 79-00-00-210-003).
F 『 EEFF : ALL E Page 40879-21-50
E E Feb 01/98 E E ECES E 5. Close-up
F 『
E C F M E
E E
E 56-5B E
E E
________ Subtask 79-21-50-410-050
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Close fan cowl doors: (Ref. TASK 71-13-00-410-040)
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
(3) Remove the warning notice(s).
F 『 EEFF : ALL E Page 40979-21-50
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
INDICATING - DESCRIPTION AND OPERATION
______________________________________
1. General
_______
(Ref. Fig. 001)
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-299, 301-302,
(Ref. Fig. 002)
R **ON A/C 106-149, 303-399, 401-499,
(Ref. Fig. 002A)
**ON A/C ALL
(Ref. Fig. 003, 004)
Oil system monitoring is performed by means of :
- indications :
oil quantity (quarts)
oil temperature (degree celsius)
oil pressure (PSI)
oil filter clogging (OIL FILTER CLOG).
These indications are displayed on the lower display unit of the ECAM system (main instrument panel) except the Master Chip Detector that gives a pop out information through its indicator in the fan compartment.
F 『 EEFF : ALL E Page 179-30-00
E E Aug 01/05 E E ECES E F 『 E C F M E E E E 56-5B E
ECAM Display Unit
Figure 001
F 『 EEFF : ALL E Page 279-30-00
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
Oil Indication Display on the ECAM System
Figure 002
F 『R EEFF : 001-049, 051-099, 101-105, 151-199, E Page 379-30-00
E E201-299, 301-302, May 01/05 E E ECES E F 『 E C F M E E E E 56-5B E
Oil Indication Display on the ECAM System
Figure 002A
F 『R EEFF : 106-149, 303-399, 401-499, E Page 479-30-00
E E Aug 01/05 E E ECES E F 『 E C F M E E E E 56-5B E
Oil System Sensors-Location Figure 003
F EEFF : E ER ECES ALL 『E 79-30-00EE E Page 5 May 01/05
F 『
E C F M E
E E
E 56-5B E
E E
INTENTIONALLY BLANK
F 『 E E Page 679-30-00
E E May 01/05 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
Oil Indicating-Electrical Power Supplies
Figure 004
F 『 EEFF : ALL E Page 7/879-30-00
E E May 01/05 E E ECES
E
F 『
E C F M E
E E
E 56-5B E
E E
OIL QUANTITY INDICATING SYSTEM - DESCRIPTION AND OPERATION
__________________________________________________________
1. General
_______
(Ref. Fig. 001, 002, 003, 004)
A. Oil Quantity Transmitter
- The oil quantity transmitter is located in the oil tank.
- The system is power supplied with 28VDC from busbar 101PP (202PP), through circuit breaker 2EN1 (2EN2).
- The oil quantity transmitter probe (tube portion) is a capacitor formed by two concentric tubes. The inner tube is shaped to achieve a linear output in a non-linear tank. The signal from this capacitor is rectified and goes to the electronics assembly on top of the transmitter.
- Transmitter specification : Output voltage : 1VDC to 9VDC varying linearly with true oil quantity from 0 to 5.45 USgal (0 - 20.62 l) Charge impedance : 33 Kohms < charge impedance < 100 Kohms Accuracy : plus or minus 0.12 USgal (0.47 l)
B. Oil Quantity Indicating
(Ref. Fig. 005, 006)
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-299, 301-302,
(Ref. Fig. 007)
R **ON A/C 106-149, 303-399, 401-499,
(Ref. Fig. 007A)
**ON A/C ALL
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM OIL 滑油(56)
