(0.40 to 2.60 m.daN)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP1008 *
trichloroethylene (Ref. 70-30-00)
Material No. CP2442 *
engine oil (Ref. 70-30-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
20 packing 79-31-15 01 -090 R 25 packing 79-31-15 01 -070
F 『 EEFF : ALL E Page 40479-31-15
E E May 01/00 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied
from the External Power 31-60-00-860-001 EIS Start Procedure 31-60-00-860-002 EIS Stop Procedure 71-13-00-010-040 Opening of the Fan Cowl Doors 71-13-00-410-040 Closing of the Fan Cowl Doors 79-31-15-991-300 Fig. 401
3. Job Set-up
__________
Subtask 79-31-15-860-050
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a warning notice is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) is off. Make sure that a warning notice is in position to tell persons not to energize the FADEC 1(2).
(3) Make sure that the access platform is in position.
Subtask 79-31-15-010-051
B. Make sure that the fan cowl doors are open: (Ref. TASK 71-13-00-010-040) FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
F 『 EEFF : ALL E Page 40579-31-15
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
4. Procedure
_________
(Ref. Fig. 401/TASK 79-31-15-991-300)
Subtask 79-31-15-420-050
A. Installation of the Oil Quantity Transmitter
(1) Remove the protective cover from the oil tank.
(2) Clean the mating surfaces:
WARNING : TRICHLOROETHANE IS A HAZARDOUS MATERIAL THAT CAN CAUSE
_______ INJURY OR ILLNESS IF NOT CORRECTLY USED. BEFORE YOU USE THIS PRODUCT, READ THE APPLICABLE MANUFACTURER'S "MATERIAL DATA SAFETY SHEET" AND OBEY THE SAFETY AND HEALTH PRECAUTIONS.
(a) To be sure of a good electrical bond between the oil quantity transmitter (15) and the oil tank, clean the mating surfaces with trichloroethylene (Material No. CP1008) and a lint-free cloth.
(3) Lubrication:
WARNING : ENGINE OIL IS A HAZARDOUS MATERIAL THAT CAN CAUSE INJURY OR
_______ ILLNESS IF NOT CORRECTLY USED. BEFORE YOU USE THIS PRODUCT, READ THE APPLICABLE MANUFACTURER'S "MATERIAL DATA SAFETY SHEET" AND OBEY THE SAFETY AND HEALTH PRECAUTIONS.
(a) Lubricate the packing (20) with engine oil (Material No. CP2442).
(4) Install the packing (20) on the transmitter (15).
R (5) Make sure that the packing (25) is installed on the oil quantity R transmitter.
R (6) Put the transmitter (15) on the oil tank and install the bolts (5) and washers (10)
R (7) TORQUE the bolts (5) to between 63 and 70 lbf.in (0.71 and 0.79 m.daN).
R (8) Remove the protective covers from the electrical connector 4002ENA and the transmitter (15).
R (9) Connect the electrical connector 4002ENA to the transmitter (15). Tighten the connector by hand plus one-eighth turn.
F 『 EEFF : ALL E Page 40679-31-15
E E May 01/00 E E ECES E
F 『
E C F M E
E E
E 56-5B E
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM OIL 滑油(59)
