• 热门标签

当前位置: 主页 > 航空资料 > 机务资料 >

时间:2011-02-24 09:14来源:蓝天飞行翻译 作者:admin
曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

__________ Subtask 20-11-11-911-053
 A. General
 (1)
 Make sure that all lockwire holes are drilled.

 (2)
 Make sure that the assembly was torqued to the requirements of the figure.

 (3)
 Use lockwire only one time.

 (4)
 Single wirelocking is permitted if the locking length is short and lies close to the component locked.

 (5)
 Double wirelocking is preferred and is essential if the locking length is long and unsupported and/or can become damaged.

 


 NOTE : Do not use lockwire to prevent unwanted operation of controls
____ or switches for any normal, standby or emergency services which can be required at any times during flight.
 4. Procedure
_________ Subtask 20-11-11-911-050
 A. Single Wirelocking
 (Ref. Fig. 201/TASK 20-11-11-991-001)

 (1)
 Put the lockwire into the hole.

 (2)
 Keep the wire tight, twist a minimum of four times.

 (3)
 Put one end through the hole in the item to which locking is to run. NOTE : Do not cut the end that is not used until the wirelocking

____ operation is completed. You can use it if the first end breaks.

 (4)
 Bend the wire back through 180. and thread it under itself.

 (5)
 Draw the wire tight and thread the end under at least two more times, making a minimum of two turns up to a maximum of four.


 Subtask 20-11-11-911-051
 B. Double Wirelocking
 (Ref. Fig. 201/TASK 20-11-11-991-001)

 (1)
 Put the lockwire into the hole in the first part and the ends equalized and bent around the head of the part.

 (2)
 Twist the strands, while tight, until the twisted part is just short of the hole in the next unit. The twisted portion must be within 3 mm (0.1181 in.) from the hole in either unit.

 


 Wirelocking Practices - Examples
 Figure 201/TASK 20-11-11-991-001
 1EFF :  ALL  1  20-11-11 Page 203 
1  1  Feb 01/98
 1  1
 1CES  1

 

 NOTE : The direction of wrap and twist of the strands must be such
____ that the loop around the part comes under the strand which protudes from the hole so that the loop stays down and does not tend to slip up and leave a slack loop.
 (3)
 Insert the highest strand through the hole in the second unit and do the above procedure.

 (4)
 After the last unit is wired, continue to twist the wires to form a pigtail of three to five twists.

 (5)
 Bend the cut ends of the pigtail in towards the item to prevent formation of a snag.


 5. Close-up
________ Subtask 20-11-11-911-052
 A. Check of the Wire
 (1)
 Trim off the remaining wire and discard.

 (2)
 Remove all pieces of off-cut wire from the aircraft structure.

 (3)
 Make sure that locking is tight.

 (4)
 Make sure that the wire shows no signs of kinking, peeling and other types of damage.

 (5)
 If no protection was applied in the wire holes before installation, you must inject the adequate protective compound after wire installation SPECIAL MATERIALS (Material No. 05-002) or SPECIAL MATERIALS (Material No. 05-027C).

 


 ELECTROSTATIC DISCHARGE SENSITIVE DEVICES - MAINTENANCE PRACTICES
_________________________________________________________________
 TASK 20-15-00-910-001
 1. Reason for the Job
 Handling Precautions for Electrostatic Discharge Sensitive Devices __________________ Self Explanatory
 2. Job Set-up Information______________________ Not Applicable __________
3. Job Set-up
 Subtask 20-15-00-860-050
 A. Not Applicable
 4. Procedure
_________ Subtask 20-15-00-912-050
 A. Handling precautions
 (1) There are no specific procedures or instructions related to this subject because:
 (a)
 The LRUs have sufficient built-in protection to prevent electrostatic discharge damage.

 (b)
 No protective electrostatic discharge handling procedures are necessary unless the LRU housing is open. For example, antistatic or conductive protective caps are not necessary for connectors on the LRU housing (standard caps are sufficient).

 (c)
 No electrostatic discharge sensitive devices printed circuit boards are LRUs. Thus it is not necessary to use wrist straps.


 NOTE : On Board Replaceable Modules (OBRMs) are not LRUs. It is
____ necessary to wear wrist straps for the Installation/replacement of OBRMs.
 
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM STANDARD PRACTICES-AIRFRAME(8)