Tightening Torques for Electrical Components
Figure 201/TASK 20-21-15-991-001
1EFF : ALL 1 20-21-15 Page 205
1 1 Feb 01/98
1 1
1CES 1
Tightening Torques for Electrical Components
Figure 202/TASK 20-21-15-991-002
1EFF : ALL 1 20-21-15 Page 206
1 1 Feb 01/98
1 1
1CES 1
Tightening Torques for Electrical Components
Figure 203/TASK 20-21-15-991-003
1EFF : ALL 1 20-21-15 Page 207
1 1 Feb 01/98
1 1
1CES 1
Tightening Torques for Electrical Components
Figure 204/TASK 20-21-15-991-004
1EFF : ALL 1 20-21-15 Page 208
1 1 Feb 01/98
1 1
1CES 1
Tightening Torques for Electrical Components
Figure 205/TASK 20-21-15-991-005
1EFF : ALL 1 20-21-15 Page 209
1 1 Feb 01/98
1 1
1CES 1
R Tightening Torques for Electrical Components Figure 206/TASK 20-21-15-991-007
1EFF : 1 1 1CES ALL 1 111 20-21-15 Page 210 Feb 01/00
R Tightening Torques for Electrical Components Figure 207/TASK 20-21-15-991-008
1EFF : 1 1 1CES ALL 1 111 20-21-15 Page 211 May 01/98
Tightening Torques for Electrical Components
Figure 208/TASK 20-21-15-991-009
1EFF : ALL 1 20-21-15 Page 212
1 1 Feb 01/98
1 1
1CES 1
Tightening Torques for Electrical Components
Figure 209/TASK 20-21-15-991-010
1EFF : ALL 1 20-21-15 Page 213
1 1 Feb 01/98
1 1
1CES 1
Subtask 20-21-15-210-051
E. Visual Inspection after Application of the Torque.
(1) After you apply the torque, make sure that:
(a)
The position of the assembled components has not changed.
(b)
The terminals are parallel.
(c)
The components are correctly locked.
(d)
You can see at least one thread and a half above the nut.
(2) Apply the identification mark (red mark) if it is necessary.
Subtask 20-21-15-912-053
F. Marking of Screws and Nuts (identification mark)
(1) After application of the tightening torque, on electrical connections held by a nut or a screw (except circuit-breakers) and made with cables with a cross-section of 5 mm2 or more (size 10 - 8 - 6, etc), you must make an identification mark (red painted line) between the
R nut or screw head and a fixed point using PAINTS FOR DETAIL (INTERNAL R AND EXTERN AL) (Material No. 07-020). (Ref. Fig. 210/TASK 20-21-15-991-011)
NOTE : You must not use the red mark as a visual reference for
____ tightening of the screw or the nut. You must remove this mark before any operation on the connection. After an operation, you must tighten the screw or the nut to the applicable torque value and repaint the red mark.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM STANDARD PRACTICES-AIRFRAME(16)