曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
automatic on some routes, for which the Automatic Dependent Surveillance -Contract (ADS-C)
function is active. In other cases, or in addition to the ADS-C reports (according to local
regulations), the pilot must send position reports by using the DCDU. Position report messages
can either be:
• Automatically–generated on the DCDU by the FMGS, if the AUTO POS REPORT function has
been set to ON, or
• Manually-prepared by the pilot on the MCDU ATC REPORTS.
For the ADS function, or for the automatic generation of position reports on the DCDU by
the FMGS, it is essential to make sure that waypoints are sequenced correctly. This is why it
is recommended to update the flight plan. The FMGS offset function should be used, when
appropriate. When the heading mode is used, the flight crew should monitor the waypoint
sequencing and clear the waypoints when necessary.
POSITION REPORTS-AUTOMATICALLY GENERATED BY THE FMGS
When sequencing a waypoint, the FMGC generates the position report message on the DCDU :
A330/A340 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
SUPPLEMENTARY PROCEDURES
INFORMATION SYSTEMS
A330/A340 FLEET PRO-SUP-46 P 14/58
FCOM 19 AUG 10
The pilot can modify the position report by using the MODIFY function key. He can then send
it to the ATC. The pilot can also use the MODIFY function key to update the parameters,
displayed on the DCDU, before sending the position report.
Pilot actions :
On the DCDU :
SEND.................................................................................................................... SELECT (1)
The message is displayed in green letters, and the OPEN status disappears.
CLOSE.................................................................................................................. SELECT (2)
The message is cleared from the screen.
POSITION REPORTS-MANUALLY PREPARED BY THE PILOT
The pilot must manually prepare position reports when the AUTO POS REPORT on the ATC
REPORTS page is set to OFF. The POSITION REPORT message must be prepared on the
MCDU.
Pilot actions :
On the MCDU’s ATC REPORTS PAGE :
MANUAL POSITION REPORT.............................................................................SELECT (1)
POSITION REPORTS pages 1/3, 2/3 and 3/3 show the data that is automatically provided
by the FMGC. The crew can manually enter some fields, if desired.
REP DISPL........................................................................................................... SELECT (2)
The report is displayed on the DCDU with a blue background. It is ready to be sent.
On the DCDU :
As for the reports that are automatically generated by the FMGS : The pilot can modify a
message that is displayed on the DCDU. This message can then be sent to the ATC by
using the SEND function key, and cleared from the screen by using the CLOSE function
key.
A330/A340 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
SUPPLEMENTARY PROCEDURES
INFORMATION SYSTEMS
A330/A340 FLEET PRO-SUP-46 P 15/58
FCOM 19 AUG 10
Applicable to: ,
POSITION REPORTS
For voice communications, a position report is due when passing a waypoint. This is entirely
automatic on some routes, for which the Automatic Dependent Surveillance (ADS) function is
active. In other cases, or in addition to the ADS reports (according to local regulations), the pilot
must send position reports by using the DCDU. Position report messages can either be :
• Automatically–generated on the DCDU by the FMGS, if the AUTO POS REPORT function has
been set to ON, or
• Manually-prepared by the pilot on the MCDU ATC REPORTS page.
A330/A340 FLIGHT CREW
OPERATING MANUAL
PROCEDURES
SUPPLEMENTARY PROCEDURES
INFORMATION SYSTEMS
A330/A340 FLEET PRO-SUP-46 P 16/58
FCOM 19 AUG 10
For the ADS function, or for the automatic generation of position reports on the DCDU by
the FMGS, it is essential to make sure that waypoints are sequenced correctly. This is why it
is recommended to update the flight plan. The FMGS offset function should be used, when
appropriate. When the heading mode is used, the flight crew should monitor the waypoint
sequencing and clear the waypoints when necessary.
POSITION REPORTS-AUTOMATICALLY GENERATED BY THE FMGS
When sequencing a waypoint, the FMGC generates the position report message on the DCDU :
The pilot can modify the position report by using the MODIFY function key. He can then send
it to the ATC. The pilot can also use the MODIFY function key to update the parameters,
displayed on the DCDU, before sending the position report.
Pilot actions :
On the DCDU :
SEND.................................................................................................................... SELECT (1)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
A330/A340机组操作手册 FLIGHT CREW OPERATING MANUAL FCOM 11(108)
