*
trichloroethylene (Ref. 70-30-00)
*
acetone (Ref. 70-30-00)
*
stoddard solvent (Ref. 70-30-00)
*
ardrox 552 (Ref. 70-30-00)
*
turco ind 79 (Ref. 70-30-00)
*
mag-chem teksol (Ref. 70-30-00)
*
degreasol 99 R (Ref. 70-30-00)
*
mag-chem skysol (Ref. 70-30-00)
F 『 EEFF : ALL E Page 80574-21-10
E E May 01/05 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
10 white chamfered silicone seal
10 blue symmetrical silicone seal
10 blue symmetrical silicone seal
10 blue symmetrical silicone seal
20 retaining ring
20 retaining ring
30 caged spring assembly
30 caged spring assembly
30 caged spring assembly
30 caged spring assembly
30 caged spring assembly
40 ceramic insulator sleeve
40 ceramic insulator sleeve
40 ceramic insulator sleeve
D. Referenced Information
74-21-10 01 -08074-21-10 01 -18074-21-10 01 -180A74-21-10 01A-18074-21-10 01 -20074-21-10 01A-20074-21-10 01 -09074-21-10 01 -19074-21-10 01 -190A74-21-10 01A-09074-21-10 01A-19074-21-10 01 -21074-21-10 01 -210A74-21-10 01A-210
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
74-21-10-000-002 Removal of the Right Ignition Lead 74-21-10-400-002 Installation of the Right Ignition Lead 74-21-10-991-304 Fig. 802
3. Job Set-up
__________ Subtask 74-21-10-020-056
A. Remove the ignition lead (Ref. TASK 74-21-10-000-002).
F 『 EEFF : ALL E Page 80674-21-10
E E May 01/05 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
4. Procedure
_________
(Ref. Fig. 802/TASK 74-21-10-991-304)
Subtask 74-21-10-350-055
A. Disassemble the Ignition Lead
PRE SB 74-002
(1) Remove and discard the white chamfered silicone seal (10).
(2) Remove the caged spring assembly (30).
(3) Remove and discard the retaining ring (20).
(4) Remove and discard the ceramic insulator sleeve (40).
(5) Replace the ignition lead if the insulation has carbon tracks and arcing damage.
POST SB 74-002
(6) Remove and discard the blue symmetrical silicone seal (10).
(7) Remove and discard the retaining ring (20).
(8) Remove and discard the ceramic insulator (40).
(9) Replace the ignition lead if the insulation has carbon tracks and arcing damage.
END OF SB 74-002
Subtask 74-21-10-160-054
B. Clean all of the ignition leads components with a lint-free cloth that is R moist with trichloroethylene (Material No. CP1008) or stoddard solvent R (Material No. CP2011) or acetone (Material No. CP1039) or ardrox 552 R (Material No. CP2559) or turco ind 79 (Material No. CP2560) or mag-chem R teksol (Material No. CP2566) or degreasol 99 R (Material No. CP2584) or R mag-chem skysol (Material No. CP2656) .
NOTE : The connector and all parts of the ignition lead must be clean.
____
F 『 EEFF : ALL E Page 80774-21-10
E E May 01/05 E E ECES E F 『 E C F M E E E E 56-5B E Subtask 74-21-10-350-056
Replacement of the Ceramic Insulator Sleeve Figure 802/TASK 74-21-10-991-304
F R EEFF : E E ECES ALL 『 E 74-21-10EEE Page 808 May 01/05
F 『
E C F M E
E E
E 56-5B E
E E
C. Assemble the Ignition Lead CAUTION : DO NOT APPLY GREASE OR ANY LUBRICANT TO THE THREADS OF THE
_______ CONNECTOR ON THE IGNITION LEAD. GREASE AND LUBRICANTS WILL CAUSE DAMAGE TO THE IGNITION LEAD AND THE SPARK IGNITER.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM IGNITION 点火(23)
