• 热门标签

当前位置: 主页 > 航空资料 > 机务资料 >

时间:2011-04-25 08:34来源:蓝天飞行翻译 作者:航空
曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

AIRPLANE MAINTENANCE MANUAL


LIST OF ILLUSTRATIONS (cont) 
FIGURE NO.  SUBJECT  GRID NO. 
74-6.  Installation of Bearings  3H17 
74-7.  Magneto Oil Seal Installation on T-125 Assembly Fixture  3H19 
74-8.  Magneto Internal Timing  3H19 
74-9.  Engine Timing Marks  3H21 
74-10.  Stipping Tool  3I2 
74-11.  Inserting Stipping Tool  3I2 
74-12.  Cutting Insulation  3I2 
74-13.  Removing Silicone Rubber from Wire  3I2 
74-14.  Installation of Plug Endnut  3I3 
74-15.  Flaring out the Shielding  3I3 
74-16.  Installation of Ferrule  3I3 
74-17.  Driving Tool  3I3 
74-18.  Insulation in Harness Cap  3I5 
74-19.  Securing Wire in Harness Cap  3I5 
74-20.  Installation of Electrode Screw  3I5 
74-21.  Installation of Insulator Sleeve  3I5 
74-22.  Installation of Spring  3I6 
74-23.  Removing Spark Plug Frozen to Bushing  3I6 
74-24.  Magneto and Starter Switches  3I9 
77-1.  Engine Instrument Lines Installation  3I15 
77-2.  Electric Tachometer Installation  3I19 
77-3.  Cylinder Head Temperature Gauge Calibration  3I22 
78-1.  Inspection of Mufflers  3J5 
79-1.  Oil Pressure Gauge Calibration  3J14 
79-2.  Oil Temperature Gauge Calibration  3J16 
80-1.  Exploded View of Gear Reduction Starter Motor  3K9 
80-2.  Turning Motor Commutator  3K12 
80-3.  Testing Motor Armature for Shorts  3K12 
80-4.  Testing Motor Fields for Grounds  3K12 
80-5.  No Load Test Hookup  3K12 
80-6.  Stall Torque Hookup  3K14 
91-1.  Tire Balancer Fixture  4B10 
91-2.  Control Surface Balancing Tool  4B21 
91-3.  Fabricated Aileron Bellcrank Rigging Tool  4B22 
91-4.  Fabricated Aileron and Flap Rigging Tool  4B23 
91-5.  Fabricated Stabilator Rigging Tool  4B24 
91-6.  Fabricated Rudder Rigging Tool  4B24 
91-7 thru 91-30. Electrical Schematics  4C6 
— Note — 
Refer to Card 4 Grid No. 4C6 for Electrical Schematic Index 

Introduction Page 18 Revised: February 28, 2002
4A22
THE NEW PIPER AIRCRAFT, INC.
PA-44-180
AIRPLANE MAINTENANCE MANUAL

LIST OF CHARTS
CHART NO. SUBJECT GRID NO.
401 Structural Inspection and Replacement 1B5
601 Leading Particulars and Principal Dimensions 1C19 1201 Thread Lubricants 1G11 2001 Maximum Distance Between Supports for Fluid Tubing 1G20 2101 Troubleshooting (Janitrol Heater) 1H6 2102 Blower System Wire Color Codes 1H11 2103 Inspection (Ignition Unit) 1I7 2401 Troubleshooting (Alternator) 1J16 2402 Troubleshooting (Battery) 1J21 2403 Alternator Belt Tension 1K1 2404 Hydrometer Reading and Battery Charge Percent 1K3 2701 Cable Tension Vs. Ambient Temperature 2B8 2702 Troubleshooting Control Surfaces 2B12 2801 Troubleshooting (Fuel System) 2E1 2802 Sender/Fuel Quantity Gauge Tolerances 2E16 2901 Leading Particulars, Hydraulic System 2F4 2902 Troubleshooting Hydraulic System 2F5 3201 Troubleshooting (Landing Gear) 2G14 3202 Toe-In, Toe-Out Correction 2H12 3401 Troubleshooting (Vertical Speed Indicator) 2K10 3402 Troubleshooting (Altimeter) 2K11 3403 Troubleshooting (Airspeed Tubes and Indicator) 2K12 3404 Troubleshooting (Magnetic Compass) 2K18 3701 Troubleshooting (Vacuum System) 2L11 3901 Troubleshooting (Annunciator Panel) 3B6 5101 List of Materials for Thermoplastic Repair 3C1 6101 Propeller Torque Limits 3F7 7101 Troubleshooting (Engine) 3F20 7301 Fuel Pressure Sender Test Specifications 3H3 7302 Troubleshooting (Fuel Pressure Gauge) 3H4 7401 Troubleshooting (Magneto) 3H10 7402 Coupling Torque 3I8 7701 Manifold Pressure Indicator (Troubleshooting) 3I17 7702 Tachometer (Troubleshooting) 3I18 7703 Cylinder Head Temperature (Troubleshooting) 3I21 7704 Exhaust Gas Temperature (Troubleshooting) 3I23 7901 Oil Pressure Sender Test Specifications 3J12 7902 Oil Pressure Gauge (Troubleshooting) 3J13 7903 Oil Temperature Indicators (Troubleshooting) 3J15 8001 Troubleshooting (Starter) 3K5 8002 Starting Motor Specifications 3K14
Introduction Page 19 Revised: February 28, 2002
THE NEW PIPER AIRCRAFT, INC.
PA-44-180
AIRPLANE MAINTENANCE MANUAL

LIST OF CHARTS (cont)

CHART NO. SUBJECT GRID NO.
9101 Flare Fitting Torques 4B5 9102 Recommended Nut Torques 4B6 9103 Decimal Conversions 4B8 9104 Decimal Equivalents of Drill Sizes 4B9 9105 List of Consumable Materials 4B11 9106 Metric Conversion Tables 4B16 9107 Electric Wire Coding 4C1 9108 Electric Symbols 4C2 9109 Electrical System Component Loads 4C5
 
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:西门诺尔飞机维护手册 simenole PA-44-180 AMM 2(87)