Introduction Page 18 Revised: February 28, 2002
3A22
THE NEW PIPER AIRCRAFT, INC.
PA-44-180
AIRPLANE MAINTENANCE MANUAL
LIST OF CHARTS
CHART NO. SUBJECT GRID NO.
401 Structural Inspection and Replacement 1B5
601 Leading Particulars and Principal Dimensions 1C19 1201 Thread Lubricants 1G11 2001 Maximum Distance Between Supports for Fluid Tubing 1G20 2101 Troubleshooting (Janitrol Heater) 1H6 2102 Blower System Wire Color Codes 1H11 2103 Inspection (Ignition Unit) 1I7 2401 Troubleshooting (Alternator) 1J16 2402 Troubleshooting (Battery) 1J21 2403 Alternator Belt Tension 1K1 2404 Hydrometer Reading and Battery Charge Percent 1K3 2701 Cable Tension Vs. Ambient Temperature 2B8 2702 Troubleshooting Control Surfaces 2B12 2801 Troubleshooting (Fuel System) 2E1 2802 Sender/Fuel Quantity Gauge Tolerances 2E16 2901 Leading Particulars, Hydraulic System 2F4 2902 Troubleshooting Hydraulic System 2F5 3201 Troubleshooting (Landing Gear) 2G14 3202 Toe-In, Toe-Out Correction 2H12 3401 Troubleshooting (Vertical Speed Indicator) 2K10 3402 Troubleshooting (Altimeter) 2K11 3403 Troubleshooting (Airspeed Tubes and Indicator) 2K12 3404 Troubleshooting (Magnetic Compass) 2K18 3701 Troubleshooting (Vacuum System) 2L11 3901 Troubleshooting (Annunciator Panel) 3B6 5101 List of Materials for Thermoplastic Repair 3C1 6101 Propeller Torque Limits 3F7 7101 Troubleshooting (Engine) 3F20 7301 Fuel Pressure Sender Test Specifications 3H3 7302 Troubleshooting (Fuel Pressure Gauge) 3H4 7401 Troubleshooting (Magneto) 3H10 7402 Coupling Torque 3I8 7701 Manifold Pressure Indicator (Troubleshooting) 3I17 7702 Tachometer (Troubleshooting) 3I18 7703 Cylinder Head Temperature (Troubleshooting) 3I21 7704 Exhaust Gas Temperature (Troubleshooting) 3I23 7901 Oil Pressure Sender Test Specifications 3J12 7902 Oil Pressure Gauge (Troubleshooting) 3J13 7903 Oil Temperature Indicators (Troubleshooting) 3J15 8001 Troubleshooting (Starter) 3K5 8002 Starting Motor Specifications 3K14
Introduction Page 19 Revised: February 28, 2002
THE NEW PIPER AIRCRAFT, INC.
PA-44-180
AIRPLANE MAINTENANCE MANUAL
LIST OF CHARTS (cont)
CHART NO. SUBJECT GRID NO.
9101 Flare Fitting Torques 4B5 9102 Recommended Nut Torques 4B6 9103 Decimal Conversions 4B8 9104 Decimal Equivalents of Drill Sizes 4B9 9105 List of Consumable Materials 4B11 9106 Metric Conversion Tables 4B16 9107 Electric Wire Coding 4C1 9108 Electric Symbols 4C2 9109 Electrical System Component Loads 4C5
THIS SPACE INTENTIONALLY BLANK
Introduction Page 20 Issued: April 1, 1997
3A24
CHAPTER
39
ELECTRICAL /
ELECTRONIC PANELS
AND
MULTIPURPOSE PARTS
THIS PAGE INTENTIONALLY BLANK
CHAPTER 39 - ELECTRICAL / ELECTRONIC PANELS AND MULTIPURPOSE PARTS TABLE OF CONTENTS / EFFECTIVITY
CHAPTER/ GRID SECTION SUBJECT NO. EFFECTIVITY
39-10-00 INSTRUMENT AND CONTROL PANELS 3B5
Removal and Replacement of Face Mounted Instruments 3B5
Annunciator Panel Troubleshooting Annunciator Replacement of Annunciator Panel Light Bulbs Removal and Installation of Vacuum Sensor Switch Removal and Installation of Oil Pressure Sensor Switch 3B5 3B5 3B7 3B7 3B7
Electric Clock Removal Installation 3B8 3B8 3B8
39-40-00 MULTIPURPOSE ELECTRICAL PARTS 3B11
Electrical Switches and Circuit Breakers Removal of Electrical Switches Installation of Electrical Switches Removal of Circuit Breakers Installation of Circuit Breakers 3B11 3B11 3B11 3B11 3B11
39- Cont./Effec. Page 39-3 Issued: April 1, 1997
THIS PAGE INTENTIONALLY BLANK
39- Cont./Effec. Page 39-4 Issued: April 1, 1997
3B4
INSTRUMENT AND CONTROL PANELS.
REMOVAL AND REPLACEMENT OF FACE MOUNTED INSTRUMENTS.
The instrument panel consists of two all metal panels without a face panel. Since all instruments are mounted in a similar manner, a description of a typical removal and installation is provided as a guide. Special care should be taken when any operation pertaining to the instruments is performed. The tagging of connections prior to removing an instrument will help in the installation process.
1.
The mounting screws for the individual instruments are exposed. Remove the connections to the instrument prior to removing the mounting screws of the instrument to be removed. Plug openings on gyro instruments immediately to prevent contamination.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：西门诺尔飞机维护手册 simenole PA-44-180 AMM 2(38)
