西门诺尔飞机维护手册 simenole PA-44-180 AMM 2(37)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

51-1.  Skin Materials and Thickness  (Sheet 1 of 2)  3B18 
51-1.  Skin Materials and Thickness  (Sheet 2 of 2)  3B19 
51-2  Surface Scratches, Abrasions or Ground-in-Dirt  3C2 
51-3.  Deep Scratches, Shallow Nicks and Small Holes  3C3 
51-4.  Mixing of Epoxy Patching Compound  3C3 
51-5.  Welding Repair Method  3C4 
51-6.  Repairing of Cracks  3C4 
51-7.  Various Repairs  3C5 
51-8.  Repair of Stress Lines  3C7 
51-9.  Repair of Impacted Damage  3C7 
52-1.  Door Snubber Installation  3C13 
52-2.  Door Installation  3C17 
52-3.  Emergency Exit Installation  3C21 
52-4.  Fabricated Tool for Baggage Door Lock  3C23 
55-1.  Stabilator Installation  3D7 
55-2.  Stabilator Balance Configuration  3D8 
55-3.  Vertical Stabilizer Installation  3D10 
55-4.  Rudder Installation  3D13 
55-5.  Rudder Balancing  3D14 
56-1.  Windshield Installation  3D23 
56-2.  Side Window Installation  3E3 
57-1.  Wing Installation  3E13 
57-2.  Aileron and Flap Installation  3E19 
57-3.  Aileron Balancing  3E21 
57-4.  Aileron Skin Repair  3E22 
61-1.  Typical Nicks and Removal Method  3F6 
61-2.  Propeller Installation  3F7 
61-3.  Propeller Governor (Sheet 1 of 2)  3F10 
61-3.  Propeller Governor (Sheet 2 of 2)  3F10 
61-4.  Propeller Unfeathering System  3F13 
71-1.  Engine and Shock Mount Installation  3G3 
71-2.  Engine Cowling Installation  3G7 
71-3.  Cowl Flap Installation  3G7 
71-4.  Induction System  3G13 
73-1.  Carburetor  3G19 
73-2.  Fuel System Schematic  3G22 
73-3  Adjustment of Engine Controls  3H1 
74-1.  Contact Points  3H12 
74-2.  Slick T-100 Assembly and Timing Tool Kit  3H13 
74-3.  Removing Coil Wedges  3H14 
74-4.  Exploded View of Slick 4300 Series Magneto  3H15 
74-5.  Index Plate and Timing Plug  3H17 

Introduction Page 17 Revised: February 28, 2002
THE NEW PIPER AIRCRAFT, INC.
PA-44-180
AIRPLANE MAINTENANCE MANUAL

LIST OF ILLUSTRATIONS (cont) 
FIGURE NO.  SUBJECT  GRID NO. 
74-6.  Installation of Bearings  3H17 
74-7.  Magneto Oil Seal Installation on T-125 Assembly Fixture  3H19 
74-8.  Magneto Internal Timing  3H19 
74-9.  Engine Timing Marks  3H21 
74-10.  Stipping Tool  3I2 
74-11.  Inserting Stipping Tool  3I2 
74-12.  Cutting Insulation  3I2 
74-13.  Removing Silicone Rubber from Wire  3I2 
74-14.  Installation of Plug Endnut  3I3 
74-15.  Flaring out the Shielding  3I3 
74-16.  Installation of Ferrule  3I3 
74-17.  Driving Tool  3I3 
74-18.  Insulation in Harness Cap  3I5 
74-19.  Securing Wire in Harness Cap  3I5 
74-20.  Installation of Electrode Screw  3I5 
74-21.  Installation of Insulator Sleeve  3I5 
74-22.  Installation of Spring  3I6 
74-23.  Removing Spark Plug Frozen to Bushing  3I6 
74-24.  Magneto and Starter Switches  3I9 
77-1.  Engine Instrument Lines Installation  3I15 
77-2.  Electric Tachometer Installation  3I19 
77-3.  Cylinder Head Temperature Gauge Calibration  3I22 
78-1.  Inspection of Mufflers  3J5 
79-1.  Oil Pressure Gauge Calibration  3J14 
79-2.  Oil Temperature Gauge Calibration  3J16 
80-1.  Exploded View of Gear Reduction Starter Motor  3K9 
80-2.  Turning Motor Commutator  3K12 
80-3.  Testing Motor Armature for Shorts  3K12 
80-4.  Testing Motor Fields for Grounds  3K12 
80-5.  No Load Test Hookup  3K12 
80-6.  Stall Torque Hookup  3K14 
91-1.  Tire Balancer Fixture  4B10 
91-2.  Control Surface Balancing Tool  4B21 
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：西门诺尔飞机维护手册 simenole PA-44-180 AMM 2(37)