5.
Attach the lead wires to their appropriate terminals of the instrument
THIS SPACE INTENTIONALLY BLANK
77-30-00 Page 77-14 Issued: April 1, 1997
3I24
CHAPTER
78
EXHAUST
THIS PAGE INTENTIONALLY BLANK
CHAPTER 78 - EXHAUST
TABLE OF CONTENTS / EFFECTIVITY
CHAPTER/ SECTION SUBJECT GRID NO. EFFECTIVITY
78-00-00 GENERAL 3I5
Description Leak Test of Muffler 3I5 3I5 1R0202
78-Cont./Effec. Page 78-3 Revised: February 28, 2002
THIS PAGE INTENTIONALLY BLANK
78-Cont./Effec. Page 78-4 Issued: April 1, 1997
3J4
GENERAL.
DESCRIPTION.
This exhaust system is a muffler system, exhaust gases are discharged through an opening in the center of the lower cowl. A heat shroud is installed for an alternate air heat rise for the carburetor. For removal of the exhaust system, the following procedures may be performed:
1.
Remove lower cowl.
2.
Remove hardware from the alternate air tube and disconnect tube from shroud.
3.
Remove hardware attaching exhaust system to engine, remove exhaust system.
4.
Reinstall the exhaust system in reverse of removal instructions.
LEAK TEST OF MUFFLER.
— Note —
Inspect each muffler slip joint for excessive exhaust leakage (See Figure 78-1). Minor discoloration and leakage is normal. If excessive leakage is evident, repair (in accordance with latest revision of AC 43.13-1) or replace as required.
Each muffler should be subjected to the following leak test:
1.
Plug muffler inlets.
2.
Connect low pressure air supply to outlet (approximately 2 psi).
3.
Submerge the muffler in water.
4.
Repair or replace any muffler that leaks.
5.
Upon completion of repairs, retest mufflers.
78-00-00 Page 78-5 Revised: February 28, 2002
THIS PAGE INTENTIONALLY BLANK
78-00-00 Page 78-6 Issued: April 1, 1997
3J6
CHAPTER
79
OIL
THIS PAGE INTENTIONALLY BLANK
CHAPTER 79 - OIL
TABLE OF CONTENTS / EFFECTIVITY
CHAPTER/ SECTION SUBJECT GRID NO. EFFECTIVITY
79-20-00 DISTRIBUTION 3J11
Oil Cooler Installation 3J11 3J11
79-30-00 INDICATING 3J11
Oil Pressure Senders Removal Testing Installation 3J11 3J11 3J11 3J12
Engine Oil Pressure Gauge Troubleshooting Removal and Replacement Calibration 3J12 3J13 3J13 3J13
Oil Temperature Gauge Troubleshooting Removal and Replacement Calibration 3J15 3J15 3J15 3J15
79-Cont./Effec. Page 79-3 Issued: April 1, 1997
THIS PAGE INTENTIONALLY BLANK
79-Cont./Effec. Page 79-4 Issued: April 1, 1997
3J10
DISTRIBUTION.
OIL COOLER.
INSTALLATION OF OIL COOLER.
1.
When installing fittings in the oil coolers, care should be used to prevent excessive torque being applied to the cooler. When a rectangular fitting boss is provided, a backup wrench should be used, employing a scissor motion, so that no load is transmitted to the cooler. When the oil cooler has a round fitting boss, care should be taken not to permit excessive torque on the fittings.
2.
If a pipe thread fitting is used, it should be installed only far enough to seal with sealing compound.
3.
Apply Lubon No. 404 to all male pipe thread fittings, do not allow sealant to enter the system.
4.
When installing hoses and fittings make sure a minimum of .5 inch clearance is maintained between hose and engine mount, and .12 inch between hose and oil filter case.
5.
If fitting cannot be positioned correctly using a torque of 10 to 15 foot-pounds, another fitting should be used.
6.
When attaching lines to the cooler, a backup wrench should be used.
7.
After installation, inspect the cooler for distorted end cups.
8.
Run-up engine, after run-up check for oil leaks.
— Note —
Winterization plates should be installed between oil cooler seal and engine baffle when ambient temperature is below 50° F.
INDICATING.
OIL PRESSURE.
REMOVAL OF OIL PRESSURE SENDERS.
There are two sending units for each engine. One for oil pressure and the other for a warning light. Both units are mounted on a common manifold located behind each engine firewall. The upper unit is for the pressure gauge and the lower unit is for the warning light. Access to the units is through access panels on each side of the forward nacelle. Removal is accomplished by the following:
1.
Disconnect the electrical leads from the particular unit. It is suggested that the leads be marked for easy connection upon reinstallation of the sensor.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：西门诺尔飞机维护手册 simenole PA-44-180 AMM 2(75)
