--------------------------------------------------------------
B. Description
(1) They are found in various sizes of similar design. These tools accommodate a large variety of dies with one, two or three crimping chambers. Die P/N selection will depend on use.
(a)
M22520/5-01 Used with interchangeable dies with 1, 2 or 3 crimping chambers (hexagon or circular).
(b)
M22520/10-01 This tool is smaller than HX4 and is used in areas where access is difficult. It is used with interchangeable dies with 1 or 2 hexagon crimping chambers.
20-25-22 Page 17
Oct 01/04
R
Hand Crimping Tool
M22520/5-01 and M22520/10-1
Figure 008
20-25-22 Page 18
Oct 01/04
R
C. Extraction of Dies
(1)
Open tool. Install dies, die groove in key. Close tool (Fig. 1).
(2)
For upper die : engage extraction tool (Fig. 2) and tap on top of tool.
(3)
For lower die : place extraction tool in position (Fig. 3) and force tool handles to open.
20-25-22 Page 19
Oct 01/04
R R
R ______________________________________________________________
8. AMP Hand Crimping Tools P/N 46121, 47386-x, 47387-x, and 48518 R (Ref. Fig. 009)
R A. Example of connection P/N used with this tool:
R --------------------------------------------------------------R | CRIMPING TOOLS | CONNECTION |
R |-------------------------|-----------------------------------|
R | NORM | P/N | P/N | TYPE |
R |------------|----------- |---------------|-------------------|
R | | 46121 | | |
R | | 47386-0 | | |
R | | 47386-2 | NSA936503 | |
R | | 47387-0 | | |
R | | 47387-2 | | TERMINALS |
R | | 48518 | | |
R | AMP |----------- |---------------| |
R | | 47386-0 | ABS0909 | |
R | | 47386-8 | | |
R | |------------|---------------|-------------------|
R | | 47386-0 | NSA936604 | END CAPS |
R | | 47387-0 | | |
R ---------------------------------------------------------------
R B. Designation
R The tool P/N is etched on the body.
R The handle end colors agree with the color of the terminal to be crimped.
R After crimping ,make sure that you can see the correct dot code on the
R terminal barrel.This shows that the tool was correct for the task.
R
R -----------------------------------------------------------------------------R | TOOL P/N | OTHER | TOOL | TOOL COLOR | WIRE | CONNECTION |
R | | TOOL P/N* | DESCRIPTION | AND DOT | GAUGE | INSULATED |
R | | | | | | COLOR |
R |-----------|-----------|---------------|--------------|-------|------------|
R | 47386-2 | -| short handles | | | |
R |-----------|-----------|---------------| one dot (.) | 14-12 | yellow |
R | | 47386 | | yellow/red | | |
R | 47386-0 | 47386-4 | long handles | | | |
R | | 409775-1 | | | | |
R |-----------|-----------|---------------|--------------|-------|------------|
R | 47387-2 | -| short handles | | | |
R |-----------|-----------|---------------| two dot (..) |20-16HD| green |
R | 47387-0 | 47387 | long handles | blue/green | 16-14 | blue |
20-25-22 Page 20
Hand Crimping Tools-AMP
46121, 47386-x,47387-x and 48518
Figure 009
20-25-22 Page 21
Oct 01/04
R -----------------------------------------------------------------------------
| TOOL P/N | OTHER | TOOL | TOOL COLOR | WIRE | CONNECTION |
| | TOOL P/N* | DESCRIPTION | AND DOT | GAUGE | INSULATED |
| | | | | | COLOR |
|-----------|-----------|---------------|--------------|-------|------------| R |-----------|-----------|---------------|--------------|-------|------------| R | 46121 | -| long handles | one dot (.) | | | R |-----------|-----------|---------------| yellow/red | 26-22 | yellow | R | 48518 | -| short handles | | | | R -----------------------------------------------------------------------------
R * a tool can have several P/Ns for the same vendor (different country of R origin,etc.)
20-25-22 Page 2220-25-22 Page 23
R ______________________________________________9. AMP Hand Crimping Tools P/N 59239-4 or 59239-8 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320 ESPM Electrical Standard Practices Manual 1(95)
