曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
which attach the guide to the roll-bar.
For the pilots' seats only.
S Make a note of the position of the
washers.
(6) Remove the shoulder strap.
AIRCRAFT
DA 40 Series
AMM Equipment/Furnishings
Doc # 6.02.01
Rev. 5 25-10-00 Page 207
20 Sep 2007
B. Install a Safety Belt
Detail Steps/Work Items Key Items/References
(1) Install the bolt and washer which attach the inertia
reel and its cover to the structure.
Refer to Figure 3.
(2) Install the bolt, washer plate and spring washer
which attach the guide to the roll-bar.
For the pilots' seats only.
(3) Put the lap straps through the holes in the seat
pan.
The buckle goes to the inboard side of
the pilots' seats (front) and the outboard
side of the passenger seat (rear).
(4) Put the lap straps between the seat pan and the
metal plate. Install the bolts with washer plates
from the top of the seat pan.
(5) Put the anchor plates in position on the bolts. For the pilots' seats only.
(6) Install washer plates and self-locking nuts on the
bolts.
Torque: 16 Nm (11.8 ft.lb).
(7) Install the seat. Refer to Paragraph 2 or 3.
7. Remove/Install the Instrument Panel Cover
A. Remove the Instrument Panel Cover
Detail Steps/Work Items Key Items/References
(1) Remove the screws which attach the instrument
panel cover to the instrument panel and the
fuselage.
(2) Lift the cover far enough to give access to the
defrost hoses.
(3) Loosen the hose clamps on the defrost hoses.
Remove the hoses from the cover.
(4) Lift the cover clear of the airplane.
AIRCRAFT
Equipment/Furnishings
DA 40 Series
AMM
Page 208
20 Sep 2007 25-10-00 Doc # 6.02.01
Rev. 5
B. Install the Instrument Panel Cover
Detail Steps/Work Items Key Items/References
(1) Do a check for unwanted items in the area
between the firewall and the instrument panel.
For example: tools.
(2) Put the instrument panel cover in position just
above the instrument panel.
(3) Connect the defrost hoses to the cover.
(4) Tighten the hose clamps on the defrost hoses.
(5) Lower the cover into position on the instrument
panel.
(6) Install the attaching screws.
8. Cleaning
A. Seats
The seat cushions are made from a fire-resistant material. Clean the cushions with a vacuum
cleaner. Use a mild soap solution to remove stains. Make sure that the area is well ventilated after
cleaning to remove all moisture.
B. Safety Belts
Use a mild soap solution to remove stains from the safety belts.
AIRCRAFT
DA 40 Series
AMM Equipment/Furnishings
Doc # 6.02.01
Rev. 5 25-60-00 Page 1
20 Sep 2007
Section 25-60
Emergency
1. General
This Section tells you about the optional Emergency Location Transmitter (ELT). It also tells you about
the Remote Control Panel/Indicator (RCPI) for the ACK E-01 ELT and the Remote Control Switch
% (RCS) for the Jolliet JE2-NG ELT, ME 406, ME 406 ACE and C 406-1. Refer to the manufacturer's
Operator’s Manual for more data.
2. Description
A. ELT Equipment
% (1) Location
% The Jolliet JE2-NG and the ACK E-01 are located below the horizontal part of the baggage
frame on the right. A bracket with one (Jolliet) or two (ACK) quick-release clamps holds the unit
in place. A bracket to the rear of the baggage frame holds the ELT antenna. The RCPI or the
RCS is located in the instrument panel, top right.
% The ME 406 and the ME 406 ACE are located in the rear fuselage, below the aft baggage
% compartment. A Velcro strap attached to a mounting bracket holds the ME 406 or the ME
% 406 ACE) in position. The ELT (ME 406 or ME 406 ACE) antenna is mounted on a bracket in
% the aft fuselage, above the ELT. If the ME 406 or ME 406 ACE are installed, a Remote Control
% Switch (RCS) is mounted on the instrument panel, right side.
% The C 406-1 is located below the horizontal part of the baggage frame on the right. A mounting
% tray, installed on a bracket holds the unit in place. A bracket aft of the ring frame holds the ELT
% antenna. The RCS is located in the instrument panel, top right. A buzzer is also installed next
% to the ELT unit which serves as a redundant warning indicator.
AIRCRAFT
Equipment/Furnishings
DA 40 Series
AMM
Page 2
20 Sep 2007 25-60-00 Doc # 6.02.01
Rev. 5
% (2) Signal Transmission
% The Jolliet JE2-NG and the ACK E-01 transmit a signal automatically after a crash on the
% emergency frequencies of 121.5 and 243.0 Megahertz (MHz). You can operate the Jolliet JE2-
% NG and the ACK E-01 manually for testing (see Maintenance Practices in this Section), or after
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
钻石40系列AMM 1(140)
