(5)
G00000 Compound - Rubbing, Parko
(6)
G00034 Cheesecloth - Clean and Lint-Free
B. References
(1) AMM 51-24-11/701, Decorative Paint System
C. Procedure
S 117-014
WARNING: DO NOT GET SOLVENTS IN YOUR MOUTH, OR YOUR EYES, OR ON YOUR
_______ SKIN. DO NOT BREATHE THE FUMES FROM SOLVENTS. SOLVENTS ARE HAZARDOUS MATERIALS. SOLVENTS MAY BE FLAMMABLE OR HARMFUL TO THE ENVIRONMENT. REFER TO PRODUCT MATERIAL SAFETY DATA SHEETS (MSDS) AND LOCAL REQUIREMENTS FOR PROPER HANDLING PROCEDURES.
(1)
Remove the marks with a clean cloth that is moist with BMS 3-2 TT-N-95 naphtha or a solution of 4 parts naphtha and 1 part isopropyl alcohol.
S 117-003
(2)
Do the step again if it is necessary until all the marks are removed.
S 117-004
(3)
Use the Parko Rubbing Compound to remove the remaining marks or discoloration.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
51-24-12
ALL ú ú 01 Page 701 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
S 117-015
(4) Repair the permanent decorative finish that is damaged during the removal (AMM 51-24-11/701).
TASK 51-24-12-307-007
3. Temporary Leeder 314N Coating - Apply
_____________________________________
A. Consumable Materials
(1)
G00034 Cheescloth - Clean and Lint-Free
(2)
B00000 Cleaner - Leeder 168D
(3)
B00192 Solvent - Cleaning, General Purpose, BMS
3-2, Type 1
(4)
B00083 Solvent - Aliphatic Naphtha, TT-N-95
(5)
G00132 Tape - Masking, No. 214, 3M Company
(6)
B00000 Leeder 314N
B. References
(1) AMM 51-21-02/701, Interior and Exterior Finishes (Prepaint Cleaning and Pretreatment)
C. Procedure
S 117-016
(1)
Remove the unwanted materials from the surface.
S 117-017
(2)
Use sand paper to remove the unwanted materias if it is necessary (AMM 51-21-02/701).
S 117-018
(3)
To clean the surface with the Leeder 168D cleaner, do the steps that follow:
(a)
Apply the Leeder 168D cleaner with the clean cheesecloth and clean the surface fully.
(b)
Before the Leeder 168D cleaner dries, dry the surface with a clean, dry cheesecloth.
(c)
Do the operation again until the cheesecloth shows no unwanted materials.
NOTE: The clean surface is overcoated in 6 hours after you
____
clean it.
S 377-008
(4)
Let the enamel paints to cure a minimum of 48 hours at room temperature before you apply the Leeder 314N.
S 117-009
(5)
Lightly clean the surface with the clean cheesecloth that is moist with the BMS 3-2 solvent or TT-N-95 naphtha.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
51-24-12
ALL ú ú 01 Page 702 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
(6) S 957-010Put 3M No. 214 tape around the areas where you will apply the coating.
(7) S 377-011Fully mix the Leeder 314N and strain it through layers of the cheesecloth.
(8) S 377-012Apply the spray of the Leeder 314N to a dry layer thickness sufficient to get a full color but no more than 2.0 mils.
(9) S 377-013Do not touch the Leeder 314N, and let it dry in 1 hour at 75°F or higher. Let the Leeder 314N dry for 4 hours at this temperature before it can get to the rain or temperature below 60°F.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
51-24-12
ALL ú ú 01 Page 703 ú Oct 10/91
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 结构 STRUCTURES(57)
