S 128-007
(2)
Rub the damaged area with 280-grit (minimum) abrasive paper.
S 118-006
WARNING: DO NOT GET PAINT MATERIALS AND SOLVENTS IN YOUR MOUTH, IN YOUR
_______ EYES, ON YOUR SKIN, OR ON YOUR CLOTHES. DO NOT BREATHE THE FUMES FROM THESE MATERIALS. MAKE SURE THE AIR FLOWS FREELY THROUGH THE WORK AREA. USE THE NECESSARY RESPIRATORY PROTECTION. KEEP THESE MATERIALS AWAY FROM SPARKS, FLAME, AND HEAT. THESE MATERIALS ARE POISONOUS AND FLAMMABLE AND CAN CAUSE INJURY OR DAMAGE. REFER TO THE APPLICABLE INDUSTRIAL HYGIENE, FIRE AND SAFETY STANDARDS FOR THE SAFE USE OF PAINT MATERIALS AND SOLVENTS.
(3)
Clean the area with a clean cheesecloth that is moist with toluene or reducer 66-C-28. Then dry the area with a clean cheesecloth.
(4)
Apply the abrasion resistant finish (AMM 51-24-04/701).
S 378-005
NOTE: Primer is not necessary unless you find bare metal.
____
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
51-24-04
ALL ú ú 01 Page 801 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 038-008
(5) Remove the masking tape.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
51-24-04
ALL ú ú 01 Page 802 ú Jun 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
INTERIOR NON-REFLECTIVE FINISH - CLEANING/PAINTING
__________________________________________________
1. General_______
A. This procedure contains one task. The task is to apply interior
non-reflective finish.
TASK 51-24-06-307-001
2. Apply the Interior Non-Reflective Finish________________________________________
A. Consumable Materials
(1)
B00094 Solvent - Toluene, ASTM D 362
(2)
B00344 Solvent - Xylene, ASTM D 846
(3)
B00151 Solvent - Methyl Isobutyl Ketone (MIBK), ASTM D 1153
(4)
B00148 Solvent - Methyl Ethyl Ketone (MEK), ASTM D 740
(5)
G00033 Cheesecloth
(6)
C00334 Coating - Nextel Suede
(a)
C00000 Primer 911 - P4
(b)
C00000 3101 Base Component I
(c)
C00000 3101 Catalyst Component II
(d)
C00000 3101 Promoter Component III
(7)
G00132 Tape, Masking 3M #214
B. References
(1) AMM 51-21-02/701, Prepaint CLeaning and Pretreatment
C. Procedure
S 117-002
(1)
Clean and prepare the surface (AMM 51-21-02/701).
S 377-003
(2)
Apply the primer, 911-P4.
(a) Mix the primer as follows:
1) Base - 2 parts (by volume)
WARNING: DO NOT GET METHYL ETHYL KETONE (MEK) IN YOUR MOUTH OR
_______ EYES, OR ON YOUR SKIN. DO NOT BREATHE THE FUMES FROM MEK. PUT ON A PROTECTIVE SPLASH GOGGLE AND GLOVES WHEN YOU USE MEK. KEEP MEK AWAY FROM SPARKS, FLAME, AND HEAT. MEK IS A POISONOUS AND FLAMMABLE SOLVENT WHICH CAN CAUSE INJURY OR DAMAGE.
2) Thinner - 1 part (by volume)
NOTE: Use a mixture of two solvents to make the base thin.
____ The mixture must have an equal quantity of each solvent. MIBK, Toluene, and MEK are satisfactory solvents. Toluene has the longest flash time and and MIBK has the shortest flash time.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
51-24-06
ALL ú ú 01 Page 701 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(b) Apply the primer on the surface with a spray gun. 1) Make sure that the dry thickness is between 0.4 mil and 1.0 mil (0.0004 to 0.001 inch).
2) Let the primer dry (minimum of 10 minutes and maximum of 60 minutes) at 70°to 90°F before you apply the Nextel Suede.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 结构 STRUCTURES(38)
