S 147-010
(6)
Clean the surface with a dry, clean cheesecloth to remove all loose and remaining particles from the area.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
51-21-04
ALL ú ú 02 Page 702 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 117-011
WARNING: DO NOT GET SOLVENTS IN YOUR MOUTH, OR YOUR EYES, OR ON YOUR
_______ SKIN. DO NOT BREATHE THE FUMES FROM SOLVENTS. SOLVENTS ARE HAZARDOUS MATERIALS. SOLVENTS MAY BE FLAMMABLE OR HARMFUL TO THE ENVIRONMENT. REFER TO PRODUCT MATERIAL SAFETY DATA SHEETS (MSDS) AND LOCAL REQUIREMENTS FOR PROPER HANDLING PROCEDURES.
(7)
Rub the surface with a cheesecloth. Make the cheesecloth moist (not soaked) with solvent, Series 88 (AMM 20-30-88/201). Clean the surface with a clean cheesecloth until no remaining particles are found on the cheesecloth.
S 917-012
(8)
Let the surface dry for a minimum of 15 minutes.
S 107-013
(9)
Remove all corrosion material found on the surface.
S 107-014
(10)
For information on the installation of sealant in the integral fuel tanks, refer to the Structural Repair Manual (SRM 51-20-05).
E. Prepare Alodine 1000 Solution
NOTE: In areas where Alodine may come in contact with BMS 10-20 primer,
____
only Alodine 600 should be used.
S 377-002
WARNING: DO NOT GET ALODINE SOLUTION IN YOUR MOUTH, IN YOUR EYES, ON
_______ YOUR SKIN, OR ON YOUR CLOTHES. DO NOT BREATHE THE FUMES FROM THIS MATERIAL. AIR MUST FLOW FREELY THROUGH THE WORK AREA. USE THE NECESSARY RESPIRATORY PROTECTION. KEEP THIS MATERIAL AWAY FROM SPARKS, FLAME, AND HEAT. THIS MATERIAL IS POISONOUS AND FLAMMABLE AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(1) To prepare the Alodine 1000 solution, do these steps:
(a) If you are using Alodine 1000L, do the steps that follow:
1) Put 6 parts (by volume) of water in a clean polyethylene container.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
51-21-04
ALL ú ú 01 Page 703 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
2) Add 4 parts (by volume) of Alodine 1000L liquid concentrate to the water.
(b)
If you are using Alodine 1000 powder, add 0.4 ounces of Alodine 1000 powder to water for each gallon of final solution.
(c)
Fully mix the Alodine solution.
(d)
Let the solution stay for an hour before it is used.
(e)
Put the Alodine 1000 solution in clean polyethylene bottles.
(f)
Identify the bottles with a label. Write the date when the solution was mixed and the date when the pot life ends.
NOTE: The pot life of the Alodine 1000 solution is 14 days.
____ Because the Alodine 1000 solution is sensitive to all types of contamination, make sure all containers are fully clean before they are used.
F. Procedure - Apply Alodine 1000 Solution
NOTE: In areas where the Alodine may come in contact with BMS 10-20
____
primer, only Alodine 600 should be used.
S 377-017
WARNING: DO NOT GET ALODINE SOLUTION IN YOUR MOUTH, IN YOUR EYES, ON
_______ YOUR SKIN, OR ON YOUR CLOTHES. DO NOT BREATHE THE FUMES FROM THIS MATERIAL. AIR MUST FLOW FREELY THROUGH THE WORK AREA. USE THE NECESSARY RESPIRATORY PROTECTION. KEEP THIS MATERIAL AWAY FROM SPARKS, FLAME, AND HEAT. THIS MATERIAL IS POISONOUS AND FLAMMABLE AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(1) Apply Alodine 1000 solution with a clean cheesecloth.
NOTE: Keep the room temperature above 65°F.
____
S 377-021
(2) Keep the part wet with the Alodine 1000 solution for 3 to 5 minutes.
NOTE: Do not let the papers or cloths dry after you apply Alodine
____ solutions. They can cause a fire when they are dry. After you use the cloths or paper soak them in water before you discard them.
S 177-022
(3) Flush the surface with water.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 结构 STRUCTURES(26)
