BACS13BX SWAGE
GROOVE DEPTH LIMITS
NOTE: ALL DIMENSIONS ARE IN INCHES.
Groove Depth Measurement for BACS13BX Sleeves
Figure 816
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-11-05
ALL ú ú 02 Page 872 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L09395
A
747-400
MAINTENANCE MANUAL
150
TORQUE WRENCH DIAL - PROCEDURE TO READ TORQUE
MATERIAL SWAGE TORQUE (POUNDS-INCH)
WALL THICKNESS - INCHESTUBE
SIZE 3AL-2.5V TITANIUM 1 21Cr-6Ni-9Mn CRES 2 MIN MAX
04 0.016 0.016 4 5
06 0.019 0.020 12 15
08 0.026 0.026 20 25
10 0.032 0.033 40 45
12 0.039 0.039 40 45
16 0.051 0.052 80 85
SWAGER TORQUES NECESSARY TO ROLLER SWAGE BACS13BX SLEEVES
TO Ti-3AL-2.5V CWSR OR 21-6-9 CRES TUBE USING HARRISON 6633K01
ROLLER SWAGING KIT
AS SPECIFIED IN SPECIFICATION AMS 4945/BMS 7-234 AS SPECIFIED IN SPECIFICATION BMS 7-185
Swage Torques, Sleeve Dimensions, and Wall Thicknesses for Roller Swaging
Figure 817 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-11-05
ALL ú ú 02 Page 873 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L09643
A
747-400
MAINTENANCE MANUAL
BACS13BX SLEEVE
DIA G
TUBE
Swage Torques, Sleeve Dimensions, and Wall Thicknesses for Roller Swaging Figure 817 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-11-05
ALL ú ú 02 Page 874 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L09645
A 747-400 MAINTENANCE MANUAL
SWAGED JOINT WALL THICKNESS (SEE TABLE)
SECTION OF ROLLER SWAGED JOINT
TUBE DIMENSIONS TUBE "NOMINAL" WALL SWAGED JOINT WALL THICKNESS FOR SIZE THICKNESS - INCHES "NOMINAL" TUBE WALLS - INCHES
3
Ti-3AL-2.5V 21-6-9 CRES
04 0.016 0.016 0.068
06 0.019 0.020 0.066
08 0.026 0.026 0.100
10 0.032 0.033 0.101
12 0.039 0.039 0.132
16 0.051 0.052 0.143
TOLERANCE +0.002 -0.003
SWAGED JOINT WALL THICKNESS SPECIFICATION
"NOMINAL" WALL THICKNESS DEFINITION: TUBE WALL THICKNESS WITHOUT TOLERANCES AS SPECIFIED BY TUBE SPECIFICATION: AMS 4945 FOR Ti-3AL-2.5V AND BMS 7-185 FOR 21-6-9 CRES.
IF THE THICKNESS OF A MEASURED TUBE WALL IS DIFFERENT THAN THE "NOMINAL", ADD OR SUBTRACT THE DIFFERENCE FROM THE NECESSARY SWAGED JOINT WALL THICKNESS FOR "NOMINAL" TUBE WALLS.
EXAMPLE: 1. MEASURED 10 SIZE TITANIUM 3AL-2.5V TUBE WALL = 0.035 INCH
2.
WALL DIFFERENCE IS 0.035 INCH, MINUS 0.032 INCH = 0.003 INCH
3.
ADD 0.003 INCH TO 0.101 INCH = 0.104 INCH
Swage Torques, Sleeve Dimensions, and Wall Thicknesses for Roller Swaging
Figure 817 (Sheet 3)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-11-05
ALL ú ú 02 Page 875 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L09724
A
747-400 MAINTENANCE MANUAL
ST878D TOOL ASSEMBLY
ST878D TOOL ASSEMBLY
Preset Pressures (PSI) for the Cherry G-85 Lockbolt Gun with ST878D Presetting Tool Assembly (BACS13AP Sleeves) Figure 818 (Sheet 1)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 STANDARD PRACTICES - AIRFRAME(46)
