~.......................................................................... | TABLE 2 | | NORMAL TUBE CLAMP MAXIMUM SPACING | ............................................................................ | Tubing | | Clamp | Clamp Spacing | | OD | | Spacing - Usual | - Special | | (Inches) | Material | (Inches) | *[1] | ............................................................................ | 1/4 | Steel, Titanium | 16.0 | 12.0 | ............................................................................ | 3/8 | Steel, Titanium | 20.0 | 15.0 | ............................................................................ | 3/8 | Aluminum | 16.5 | 12.0 | ............................................................................ | 1/2 | Steel, Titanium | 23.0 | 17.0 | ............................................................................ | 1/2 | Aluminum | 19.0 | 14.0 | ............................................................................ | 5/8 | Steel, Titanium | 22.0 | 18.5 | ............................................................................ | 5/8 | Aluminum | 22.0 | 16.5 | ............................................................................ | 3/4 | Steel, Titanium | 27.5 | 20.5 | ............................................................................ | 3/4 | Aluminum | 24.0 | 18.0 | ............................................................................ | 1.0 | Steel, Titanium | 30.0 | 22.5 | ............................................................................ | 1.0 | Aluminum | 26.5 | 19.5 | ............................................................................ | 1 1/4 | Steel, Titanium | 31.5 | 23.5 | ............................................................................ | 1 1/4 | Aluminum | 28.5 | 21.0 | 2...............….................…........................…...............1
*[1] Special: Wing Rear Spar, Engine Strut, Engine Aft Fairing
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-11-05
ALL ú ú 01 Page 412 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
BACS13AP
BACS13BD SLEEVE
LUBRICATION POINTS
Flareless Tubing Assembly Lubrication Points
Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-11-05
ALL ú ú 01 Page 413 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
E47329
A
747-400
MAINTENANCE MANUAL
1
MAKE SURE THE DECREASE OF ID IS NOT MORE THAN
0.005 INCH AFTER PRESET OR 0.015 INCH AFTER MANY TIGHTENINGS
Maximum Collapse of Preset Flareless Sleeve Figure 402
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
20-11-05
ALL ú ú 01 Page 414 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
TUBING SIZE (INCHES) NOTE:____ USE CARE WHEN SELECTING CORRECT TORQUE FOR REDUCER FITTINGS INSTALLATION TORQUE. FITTINGS. THE BOSS OR BULKHEAD SIZE DETERMINES INSTALLATION TORQUE ON FLARELESS TUBING FITTINGS (POUND-INCHES, |5%) 3 4
OD TUBE DASH NO. STEEL & TITANIUM TUBES 1 ALUMINUM & ANNEALED CRES TUBES 2
3/16 -3 100 80
1/4 -4 140 110
5/16 -5 190 140
3/8 -6 270 170
1/2 -8 500 280
5/8 -10 700 360
3/4 -12 900 450
1 -16 1200 750
1-1/4 -20 1600 900
1-1/2 -24 2000 900
2 -32 2000 ---
TORQUE VALUES APPLICABLE TO THE FOLLOWING TUBE ENDS:
A. 21-6-9 CRES AND ALL OTHER CRES TUBE ENDS WITH BACS13BD OR BACS13BX SWAGED SLEEVES
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 STANDARD PRACTICES - AIRFRAME(15)
