曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
FLIGHT COMPARTMENT
1. General
The flight compartment contains fixed seats for 2 pilots. Each pilot has a safety belt. The fuselage
shell has fabric wall panels. GFRP or CFRP moldings make the instrument panel cover and the
center console. See Chapter 25-60 for data about the ELT.
2. Description
A. Pilot’s Seats
Each pilot’s seat has 3 parts. It has a molded GFRP backrest which is integral with the
bulkhead. It has a molded GFRP or CFRP seat pan which also makes the outer arm rest for the
seat. And it has a full-length padded seat cushion.
B. Safety Belts
Each pilot’s seat has a four-point safety belt with a central lock. The pilot can adjust each of the
4 straps to give the correct fit. Shoulder straps with inertia reels are optional. Replace frayed or
damaged straps.
C. Fabric Wall Panels
Fabric wall panels bond to the inside of the fuselage shell. Each panel has a map pocket.
Optionally some aircraft may have GFRP or CFRP wall panels with fabric coverings. The panels
are attached with Velcro and screws.
D. Instrument Panel Cover
A GFRP or CFRP cover goes over the instrument panel. The outer face of the cover is painted.
The cover has two air vents for avionic cooling. The air vents are used as hand-holds to help
the pilot’s to go in or out of the cockpit. Screws attach the cover to the instrument panel.
The instrument panel cover has a de-frost manifold. The de-frost manifold connect to the cabin
heating system. The manifold supplies warm air to the front of the canopy to prevent misting.
E. Center Console Access Panel
The center console has an access panel for the controls in the center console.
F. Baggage Compartment Floor Panel
The baggage compartment floor has 3 pieces. You can remove the center piece by itself. The
outer pieces make stowage boxes. The pieces are made of GFRP or CFRP.
Equipment/Furnishings
DA20-C1 AMM
Page 2
30 Apr 2009 25-10-00 Doc # DA201-C1
Rev. 15
G. Baggage Net
A net attaches to the front of the floor panel. Quick-release hooks attach it to the roll bar.
DA20-C1 AMM
Equipment/Furnishings
Doc # DA201-C1
Rev. 15 25-10-00 Page 3
30 Apr 2009
Figure 1: Flight Compartment Furnishing Locations
Equipment/Furnishings
DA20-C1 AMM
Page 4
30 Apr 2009 25-10-00 Doc # DA201-C1
Rev. 15
Intentionally left blank
DA20-C1 AMM
Equipment/Furnishings
Doc # DA201-C1
Rev. 0 25-10-00 Page 201
19 Dec 1997
MAINTENANCE PRACTICES
1. General
These maintenance practices tell you how to remove/ install the seats and other furnishings. See
Chapter 25-60 for data about the ELT.
2. Remove/Install a Pilot’s Seat
A. Remove a Pilot’s Seat
Detail Steps/Work Items Key Items
(1) Release the press-studs which hold the seat
cushion. And remove the seat cushion.
(2) Remove the boot for the control stick.
(3) Remove the 5 screws from the seat shell.
(4) Lift the seat a little:
−• Release the quick-release fastener for
the outer strap.
−• Move the inner strap through the hole
in the seat shell.
Take care not to loose the rubber strips
from the holes.
(5) Remove the seat shell.
B. Install a Pilot’s Seat
Detail Steps/Work Items Key Items
(1) Make sure that there are no unwanted items
below the seat.
(2) Make sure that the outer strap is in position
in the seat shell.
(3) Move the inner strap through the hole in the
seat shell.
Make sure that the rubber strips are in
position on the hole.
(4) Put the seat shell in position.
(5) Install the attaching screws.
(6) Install the boot for the control stick.
(7) Install the seat cushion.
Equipment/Furnishings
DA20-C1 AMM
Page 202
29 Apr 2004 25-10-00 Doc # DA201-C1
Rev. 9
Figure 2: Safety Belt Installation
DA20-C1 AMM
Equipment/Furnishings
Doc # DA201-C1
Rev. 9 25-10-00 Page 203
29 Apr 2004
3. Remove/Install a Safety Belt
A. Remove a Safety Belt
Detail Steps/Work Items Key Items
(1) Release the bolts which attach the shoulder
straps, or remove the cover and the 3
screws which attach the inertia reels
Refer to Figure 2.
(2) Remove the seat shell. Refer to paragraph 2 above.
(3) Remove the lap strap with the central lock by
releasing the quick release.
(4) Loosen the mounting bolt for the lap strap
without a central lock. Pull the strap from the
mounting, or release the quick release.
B. Install a Safety Belt
Detail Steps/Work Items Key Items
(1) Connect the lap strap without the central lock
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
钻石20系列AMM 1(87)
