曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
− Read the oil contents from the dip-stick.
CAUTION: USE ONLY THE CORRECT ENGINE OILS. REFER TO THE
TELEDYNE CONTINENTAL MAINTENANCE MANUAL FOR THE
CORRECT ENGINE OIL SPECIFICATIONS. IF YOU DO NOT USE THE
CORRECT ENGINE OIL, THE ENGINE CAN BE DAMAGED.
(4) If necessary, fill the oil system to the correct
level.
(5) Install the filler cap.
(6) Close the access panel in the cowling.
DA20-C1 AMM
Servicing
Doc # DA201-C1
Rev. 4 12-10-00 Page 5
12 Jan 2001
Table 1 - Engine Oil
All seasonal weight:
All temperatures ...........................................................................................15W50
All temperatures ...........................................................................................20W50
Below 40ºF (4.5ºC) Ambient air, sea level ...................................................SAE30 or 10W30
Above 40ºF (4.5ºC) Ambient air, sea level...................................................SAE50 or 20W60
Servicing
DA20-C1 AMM
Page 6
12 Jan 2001 12-10-00 Doc # DA201-C1
Rev. 4
4. Brake System
The brake fluid reservoirs are located on the brake master cylinders on the co-pilots side. You get
access in the cockpit below the instrument panel.
WARNING: DO NOT GET BRAKE FLUID ON YOUR SKIN OR IN YOUR MOUTH.
BRAKE FLUID CAN CAUSE DISEASE.
CAUTION: REMOVE SPILLED BRAKE FLUID IMMEDIATELY. BRAKE FLUID CAN
CAUSE DAMAGE TO PAINT AND OTHER MATERIALS.
A. Fill the Brake System Reservoirs
Detail Steps/Work Items Key Items
(1) Clean the top of the brake fluid reservoir and
filler cap.
(2) Remove the filler cap.
(3) Fill the reservoir to the correct level. Use only MIL-H-5606A hydraulic fluid.
12 to 25 mm (0.5 to 1 in) below the top of the
filler hole.
(4) Install the filler cap.
5. Tires
The DA20-C1 has these tires:
− Main tire: 5.00 x 5 - pressure 33 psi (2.3 bar).
− Nose tire: 5.00 x 4 - pressure 26 psi (1.8 bar).
A. Examine the Tires and Measure the Pressure
Detail Steps/Work Items Key Items
(1) Examine the tires. Look specialy for:
− Cuts and friction damage.
− Correct alignment of the red slip marks.
Move the airplane as necessary so that each
part of each tire can be seen.
If the slip marks do not align, remove the
wheel for shop maintenance.
(2) Measure the tire pressure. If necessary,
inflate the tires to the correct pressure.
Main tire: 33 psi (2.3 bar).
Nose tire: 26 psi (1.8 bar).
DA20-C1 AMM
Servicing
Doc # DA201-C1
Rev. 15 12-20-00 Page 1
30 Apr 2009
CHAPTER 12-20
SCHEDULED SERVICING
1. General
This Section gives lubrication data. It tells you where components are located and gives a list of
approved lubricants. It also gives the components which MUST NOT be lubricated.
Most systems and components have maintenance-free bearings. These can be sealed ball/roller
bearings or Teflon bushings. These bearings MUST NOT be lubricated.
Table 1 shows the items which MUST NOT be lubricated.
Table 1 - Items Which MUST NOT be Lubricated
Rudder pedal sled. DO NOT LUBRICATE
Flap rod-end bearings. DO NOT LUBRICATE
Aileron rod-end bearings. DO NOT LUBRICATE
Elevator rod-end bearings. DO NOT LUBRICATE
Nose wheel bearings. (1) DO NOT LUBRICATE
Throttle control cable. (2) DO NOT LUBRICATE
Elastomeric spring. (3) DO NOT LUBRICATE
Notes:
(1) The nose wheel bearings are sealed and maintenance-free.
(2) The throttle control cable is sealed and maintenance free.
(3) The elastomeric spring is maintenance free.
Servicing
DA20-C1 AMM
Page 2
30 Apr 2009 12-20-00 Doc # DA201-C1
Rev. 15
2. Lubrication Schedule
Table 2 shows the lubrication schedule. Clean each lubrication point before lubrication.
See Figures 1 and 2 for the location of the lubrication points listed on the left side of the table.
Refer to Table 3 for the type of lubricant that is required for each item.
The right column shows the lubrication interval.
Table 2 - Lubrication Schedule
Location Type (See Table 3) Interval
No See Figures 1 and 2 1 2 3 4 5 6 (Hours) (1) (2)
(NS) Parking brake, cabin heat, defrost, and alternate
air control cables
• 200
1 Brake pedal pivot • 200
2 Rudder cable S-tubes • 200
3 Flap actuator universal pivot block • 1000
4 Stick support pivot pins • 1000
5 Flap actuator extension rod • 200
6 Upper rudder pivot bearing • 200
7 Main wheel bearings (3) • 200
8 Brake caliper locating pins • 200
9 Nose landing gear fork pivot (4) • 200
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
钻石20系列AMM 1(51)
