737-300 400 500 AMM 飞机维护手册 机身 FUSELAGE(5)

曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 D.  The keel beams comprise the beam between the main landing gear wheel wells and the beam which passes beneath the center wing box. The beam between the wheel wells is a reinforced box structure which carries pressurization loads originating on the sealed floor structure across the wheel well area. Both of the beams carry the bending loads acting along the lower fuselage across the cavities for the center wing box and the wheel well. A blowout panel is in the lower surface of the keel beam forward of the main wheel well.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 53-12-00
 ALL  ú ú B02 Page 1 ú Oct 25/84
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 KEEL BEAM BLOWOUT PANEL - REMOVAL/INSTALLATION
______________________________________________
 1.  General_______
 A.  The blowout panel of the keel beam is on the centerline of the airplane, forward of the main wheel well. The function of the panel is to release the pressure that is too high in the keel beam because of a broken APU duct. The panel is hinged and will blow open when special attach rivets are sheared. The panel has a deflector to keep the panel open in flight. Decals give the replacement rivets.
 TASK 53-12-11-404-001-B00
 2.  Keel Beam Blowout Panel Installation____________________________________
 A.  Special Tools and Equipment
 (1)  Rivets - MS20470A, 1/8-inch diameter
 B.  Standard Tools and Equipment
 (1)  Wooden or plastic spatula
 C.  Consumable Materials
 (1)  
A00247 Sealant - BMS 5-95 Class B-2 and parting agent

 (2)  
B00148 Solvent - Methyl Ethyl Ketone

 D.  References
 (1)  
20-30-11, Adhesives, Cements and Sealants

 (2)  
20-30-31, Cleaners and Polishes

 E.  Procedure - Keel Beam Blowout Panel Installation
 S 164-002-B00
 (1)  Clean the unwanted material where it is necessary.
 F.  Prepare for the Installation
 S 114-013-B00
 WARNING: DO NOT GET METHYL ETHYL KETONE (MEK) IN YOUR MOUTH OR EYES, OR
_______ ON YOUR SKIN. DO NOT BREATHE THE FUMES FROM MEK. PUT ON A PROTECTIVE SPLASH GOGGLE AND GLOVES WHEN YOU USE MEK. KEEP MEK AWAY FROM SPARKS, FLAMES, AND HEAT. MEK IS A POISONOUS AND FLAMMABLE SOLVENT WHICH CAN CAUSE INJURY OR DAMAGE.
 (1)  
Remove and clean the sealant that remains from the mating surfaces with a wooden or plastic spatula.

 (2)  
Clean the area with the solvent.

 S 214-004-B00

 (3)  
Apply the parting agent to external faces of the fairing mating surface (Ref 51-31-00/201).

 S 114-012-B00
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 53-12-11
 ALL  ú ú B01 Page 401 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 624-010-B00
 CAUTION:_______ APPLY PRESSURE WITH YOUR HAND TO INSTALL THE PANEL.  DO NOT
 DAMAGE OR PRELOAD THE PANEL DURING THE INSTALLATION.  REMOVE
 ALL THE UNWANTED SEALANT FROM THE INNER AND THE OUTER AREA OF
 THE PANEL.  USE THE MINIMUM SEALANT TO PREVENT A PANEL OUT OF

 THE FAIR CONDITION.
 (4)  Apply the sealant to the inner faces of the panel mating surfaces immediately before the panel installation.
 NOTE: You can apply the sealant as a continuous or broken
____ seal (Ref 51-31-00/201).
 S 214-006-B00
 (5)  
Examine the attachment clips for damage. S 214-007-B00

 (6)  
Examine the door for free motion at the hinge line.

 S 424-008-B00 CAUTION: USE THE RECOMMENDED RIVETS TO GET THE CORRECT FUNCTION OF THE
_______ BLOWOUT PANEL.
 (7)  
If the panel has opened due to excess pressure, then re-install the panel to the "T" structure with two rivets.

 S 424-014-B00

 (8)  
If the panel has been open for inspection, then attach the panel assembly to airplane with 4 screws.
　
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 机身 FUSELAGE(5)