(2)
G00508 Compound - Corrosion preventive, MIL-C-11796, Class 3
(3)
A00249 Compound - Sealing, BMS 5-26, Type II, Class A-2
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
53-51-20
ALL ú ú B02 Page 401 ú Nov 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
Mid Wing-To-Body Fairing
Figure 401 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
53-51-20
ALL ú ú B02 Page 402 ú Nov 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
G94693
A 737-300/400/500MAINTENANCE MANUAL
B
C
Mid Wing-To-Body Fairing
Figure 401 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
53-51-20
ALL ú ú B02 Page 403 ú Nov 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
G94694
D.
E.
F.
A
737-300/400/500MAINTENANCE MANUAL
(4)
A00247 Sealant - Chromate, BMS 5-95, Type IReferences
(1)
AMM 12-31-21/201, Body Section 43 Access Doors and Panels
(2)
AMM 12-31-31/201, Body Section 46 Access Doors and Panels
(3)
SWPM 20-20-00, Standard Wiring Practices Manual
(4)
AMM 20-30-11/201, Adhesives, Cements, and Sealers
(5)
AMM 51-21-95/701, Skin and Fastener Corrosion Removal and Control
(6)
AMM 51-31-00/000, Seals and Sealing
(7)
AMM 51-51-00/801, Bonded Rub PadsAccess
(1)
Location Zones 300/400 Left Wing/Right Wing
Procedure
S 214-008-B00
(1) Examine the mating surfaces on the structure and the fairing panel.
(a) Make sure all mating surfaces are clean and free from any contamination or painting.
S 214-009-B00
(2) Make sure the teflon rubstrip is in a good condition.
(a) If it is necessary, repair the teflon rubstrip (AMM
51-51-00/801).
S 214-010-B00
(3) Make sure the fasteners and the area around the fastener holes are clean.
NOTE: Fastener locations with stainless steel fasteners are
____ usually at 4 locations per panel, (1) at each corner.
S 024-011-B00
(4)
Remove any paint or primer covering the conductive surface at the panel in the area underneath dimpled washer.
S 214-012-B00
(5)
If the conductive surface is flame sprayed aluminum, do the following:
(a)
Apply alodine over exposed aluminum
(b)
Install fasteners (stainless bolt and dimpled washer).
(c)
Measure the resistance.
1) Maximum resistance shall not exceed 0.5 OHMs.
(d)
Touch up finish
S 214-013-B00
(6) If the conductive surface is anti-static coating, do the following:
(a)
Apply anti-static paint over exposed area
(b)
Install fasteners (stainless steel bolt and dimpled washer)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
