EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
53-31-31
ALL ú ú B01 Page 403 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
S 034-005-B00
(2)
To remove the upper seal plate, move the stabilizer to the full down position.
S 034-006-B00
(3)
Remove the pins that connect the link assemblies to the pedestal.
S 034-007-B00
(4)
Pull out the sliding seal plate.
S 034-008-B00
(5)
Remove all the hardware from the seal plate.
NOTE: Keep the link assembly and the corner plates for
____
installation.
TASK 53-31-31-404-009-B00
3. Stabilizer-to-Body Front Spar Sliding Seal Installation
_______________________________________________________
A. Consumable Materials
(1) G00000 - Mylar Tape
B. Access
(1) Access Panels
9119 Gap Cover Upper, Left Side
9219 Gap Cover Upper, Right Side
9120 Gap Cover Upper, Left Side
9220 Gap Cover Upper, Right Side
9117 Gap Cover Upper, Left Side
C. The Replacement Sliding Seals Installation (Fig. 401)
S 434-010-B00
(1)
Adjust the link assembly on the center of the replacement seal plate.
S 214-011-B00
(2)
Make sure that the tie-bar lugs are clear of the seal plate edges and the edge distances will be satisfactory.
S 214-037-B00
(3)
Make a mark for the location of the tie-bar on the seal plate with a pencil.
S 144-012-B00
(4)
Clean the tracks and the area which is near the tracks to remove the contamination or the unwanted material.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
53-31-31
ALL ú ú B01 Page 404 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 434-013-B00
(5) Temporarily attach the link assembly to the pedestal.
NOTE: Do not install the cotter pins.
____
S 434-014-B00
(6)
Wind the protective Mylar tape around the end of the track strip as shown to prevent the seal plate from damage during the installation.
S 434-015-B00
(7)
Put the seal plate into the tracks.
NOTE: You must bend the plate in the opposite direction during the
____
installation to remove the stabilizer.
S 434-016-B00
(8)
Use the index mark to align the seal plate on the link assembly.
S 434-040-B00
(9)
Lightly attach the seal plate to the tie-bar with a clamp.
S 434-017-B00
(10)
You get equal dimensions when you move the seal plate in a longitudinal direction where it is necessary.
NOTE: The dimensions are between the etched line on the seal plate
____ and the edges of the track strip along the full length of the track that you can see.
S 954-042-B00
CAUTION:_______YOU MUST DO THE STEP BELOW CAREFULLY. IF THE CHIPS GO INTO THE TRACKS, IT CAN CAUSE DAMAGE TO THE TEFLON SEAL.
(11) Apply the tape to all the track openings, until the drilled chips can not go into the track.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
53-31-31
ALL ú ú B01 Page 405 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 434-019-B00
(12)
Tighten the clamps.
S 434-020-B00
(13)
Back drill, a minimum of two locations through the holes in the tie-bar into the seal plate.
S 434-021-B00
(14)
Install the temporary cleco fasteners in the holes.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 机身 FUSELAGE(14)
