- complete the installation of the FQIC (3QT) (Ref. AMM TASK 28-42-34-000-001) and (Ref. AMM TASK 28-42-34-400-001).
(3) If the message L DUALCOMP 53QT or L DUALCOMP 53QT/WRG is shown:
(a) Remove the temporary installed serviceable FQIC 3QT (Ref. AMM TASK 28-42-34-000-001) and return it to stores.
(b) Get access (Ref. AMM TASK 28-42-43-000-008) to the:
- tank wall connectors 4039VC1-A and 4040VC1-A
- shorting plugs 4041VC-A and 4043VC-A.
1 Disconnect the:
_
- tank wall connectors 4039VC1-A and 4040VC1-A
- shorting plugs 4041VC-A and 4043VC-A.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : 301-399, ∞∞28-42-00∞∞∞∞∞∞∞∞∞∞Page C207
Aug 01/05 CES
(4) Do a visual inspection and electrical tests of the aircraft wiring (Ref. AWM 28-42-05), (Ref. AWM 28-42-11) and (Ref. AWM 28-42-13) between the FQIC rack connector 3QT-A and the tank wall connectors 4039VC1-A and 4040VC1-A as follows:
NOTE : Each capacitive fuel probe is supplied with an alternating
____ current drive from the FQIC. The fuel probes in a tank group (harness) share the drive and drive return (two aircraft wires) between the FQIC rack connector and the connectors 4041VC-A and 4043VC-A. The connectors 4041VC-A and 4043VC-A are adjacent to and below their related tank wall connectors 4039VC1-A and 4040VC1-A. In the connectors 4041VC-A and 4043VC-A (shorting plugs):
- the drive wire divides to supply each of the related fuel probes, in parallel
- the drive return wire also divides to connect to each of the related fuel probes,in parallel. All of the discrete drive and drive return wires then go to the tank wall connectors 4039VC1-A and 4040VC1-A. Diodes located on a circuit card assembly in the dualcomp half wave rectify the output signals. The positive going, dc current signals (in proportion to the capacitance value/fuel dielectric permittivity) are routed directly from the tank wall connectors 4039VC1-A and 4040VC1-A to the FQIC rack connector. The drive inputs and signal outputs from:
- dualcomp A are routed to the FQIC 3QT through the left wing wiring group A
- dualcomp B are routed to the FQIC 3QT through the left wing wiring group B.
(a) Visual Inspection Make sure that good lighting is available. Do a visual inspection and look for distortion (bent, pinched or stretched), damage (broken, chafed or cut), discoloration, overheating (burnt, melted or arcing), liquid contamination, loose electrical connection, or incorrect assembly of the items that follow:
Left Wing Group A (Ref. AWM 28-42-05)
- FQIC rack connector 3QT-A, pins 1D, 3C and 1E
- 92VU shelf receptacle 214VC and connector 214VC-A
- receptacle 1521VC and connector 1521VC-A
- receptacle 2973VC and connector 2973VC-A
- receptacle 7107VC and connector 7107VC-A
- pressure seal feedthrough 4015VP
- shorting plug 4041VC-A and receptacle 4041VC
- connector 4039VC1-A, pins <Z, GG and AA
- adjacent and related connecting wires
- FQIC rack connector 3QT-A, pins 4J, 7G and 5F
Left Wing Group B (Ref. AWM 28-42-11) and (Ref. AWM 28-42-13)
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : 301-399, ∞∞28-42-00∞∞∞∞∞∞∞∞∞∞Page C208
Aug 01/05R CES
- 92VU shelf receptacle 210VC and connector 210VC-A
- receptacle 1970VC and connector 1970VC-A
- receptacle 7155VC and connector 7155VC-A
- pressure seal feedthrough 4017VP
- shorting plug 4043VC-A and receptacle 4043VC 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址:A320 Trouble Shooting Manual 排故手册 FUEL 燃油3(60)