F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E
Borescope Inspection of the Stage 4 Booster Blades Figure 604/TASK 72-21-00-991-310
F EEFF : E ER ECES ALL 『E 72-21-00EE E Page 612 Nov 01/02
Booster Rotor Blades Damage Inspection (All stages) Figure 605/TASK 72-21-00-991-313
F EEFF : E ER ECES ALL 『E 72-21-00EE E Page 613 Nov 01/02
F 『
E C F M E
E E
E 56-5B E
E E
(1) Connect the BORESCOPE - LIGHT SOURCE SET (856A1322P02/P03/P04/P07/P08) to a grounded power supply.
(a) Connect the fiber light cable to the BORESCOPE KIT (856A1320P04/P05) and to the port on the BORESCOPE - LIGHT SOURCE SET (856A1322P02/P03/P04/P07/P08).
(b) Turn the light source on. Engage the borescope and the long right-angle extension, and set it as necessary for inspection.
Subtask 72-21-00-290-054
C. Borescope Inspection of the booster blades.
WARNING : USE CARE TO AVOID PERSONAL INJURY WHEN YOU MANUALLY TURN THE
_______ FAN ROTOR. ASSURE SAFE FOOTING.USE HEAVY PROTECTIVE GLOVES
(1) Do an borescope inspection of the booster blades while you turn the fan rotor clockwise (aft looking forward) to complete the procedure.
-------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
1. Booster rotor blades (all stages) for:
A. Missing piece on Axial or radial depth
tip corner 0.25 in. (6.35 mm) max.
B. Cracks Not serviceable
C. Wear or local Axial depth 0.5 in.
deformation (blade (12.7 mm) and 0.8 in.
tip corner on (20.32 mm) radial max.
leading and/or
trailing edges
D. Nicks, dents on No limited quantity if
concave and/or not deeper than 0.01 in.
convex sides (0.25 mm)
located in area E
E. Nicks, dents on No limited quantity if
concave and/or not deeper than 0.04 in.
F 『 EEFF : ALL E Page 61472-21-00
E E Nov 01/02 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
-------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS
-------------------------------------------------------------------------------convex sides not (1.02 mm) located in area E
F. Nicks, dents, on Axial depth 0.02 in.
leading and/or mex (0.5 mm) max.
trailing edges
NOTE : If any damage is found, do a borescope inspection of all booster
____
downstream stages and compressor.
G. Distorted leading Circumferential
and/or trailing displacement 0.2 in. (5
edges not located mm) maximum
in area E
NOTE : Whenever
____ serviceable limits for the following are exceeded, refer to the over-serviceable limit extension if necessary (Ref. TASK 72-00-00-200-025).
(2) When the inspection is completed, turn the switch off. Leave the main light source blower on for a while to cool the lamp and the housing.
5. Close-up
________
Subtask 72-21-00-410-061
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Close the thrust reverser doors: (Ref. TASK 78-36-00-410-040). FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR
F 『 EEFF : ALL E Page 61572-21-00
E E Nov 01/02 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(3) Remove the access platform(s).
Subtask 72-21-00-440-052
B. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041).
Subtask 72-21-00-410-062
C. Close Access
(1) Close the fan cowl doors: (Ref. TASK 71-13-00-410-040) FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
(2) Remove the warning notice(s).
F 『 EEFF : ALL E Page 61672-21-00
E E Nov 01/02 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
TASK 72-21-00-210-009
Inspect Fan Rotor Blades Installed on the Fan Disk
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM ENGINE 发动机 1(98)
