1EFF : ALL 1 22-62-11Page 402 1 1 Feb 01/99 1 1 1CES 1
RUD TRIM Control Switch
Figure 401/TASK 22-62-11-991-002
1EFF : ALL 1 22-62-11 Page 403
1 1 Feb 01/98
1 1
1CES 1
(4)
Loosen the four screws (1) that attach the plate (7) to the structure
of the panel 110VU (11).
(5)
Remove the plate (7).
(6)
Remove the nut (13) from the control switch (12).
(7)
Remove the control switch (12) from the structure of the panel 110VU (11).
(8)
With an ELECTRICIAN SERVICE TOOL KIT (DMC519) disconnect and make a mark on each wire of the control switch connector. If necessary, cut the tie wraps of the control switch harness or remove the rear of the panel 110VU.
(9)
Remove the control switch (12).
1EFF : ALL 1 22-62-11Page 404 1 1 Feb 01/98 1 1 1CES 1
TASK 22-62-11-400-001
Installation of the RUD TRIM Control Switch (9CC)
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED DOORS - COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE WHEEL CHOCKS ARE IN POSITION._______
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ GEAR.
1. Reason for the Job__________________
Self Explanatory
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
R R No specific DMC519 Torque Wrench : range 0.00 to 1.20 m.daN (0.00 to 9.00 lbf.ft)1 ELECTRICIAN SERVICE TOOL KIT
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R 22-62-00-710-001 22-96-00-710-001 22-97-00-710-001 32-45-00-710-001 22-62-11-991-002 Operational Test of the Rudder Trim FunctionOperational Test of the AFSOperational Test of the LAND CAT III Capability Operational Check of the Parking Brake System Using Individual Motors in TurnFig. 401
1EFF : ALL 1 22-62-11Page 405 1 1 May 01/05 1 1 1CES 1
3. Job Set-up
__________
Subtask 22-62-11-865-051
A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AUTO FLT/FAC1/28VDC 5CC1 B04 121VU AUTO FLT/RUDDER/TRIM/IND 15CC M20 121VU AUTO FLT/FAC2/28VDC 5CC2 M19 121VU HYDRAULIC/PARK BRK/CTL/STBY 71GG N37 121VU HYDRAULIC/PARK BRK/CTL/NORM 70GG N36
R 122VU LIGHTING/INSTL LT/MAIN INST/PNL AND/PED 4LF Y04
4. Procedure
_________
Subtask 22-62-11-420-050
A. Installation of the RUD TRIM Control Switch (9CC)
(Ref. Fig. 401/TASK 22-62-11-991-002)
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
On the rear of the control switch (12) with the ELECTRICIAN SERVICE TOOL KIT (DMC519) connect each wire in its initial position (refer to the marks).
(4)
Install the control switch (12) on the structure of the panel 110VU (11). NOTE: Make sure that the equipment locating pin goes in its housing.
(5)
Attach the control switch (12) to the structure of the panel 110VU
(11) with the nut (13).
(6)
Torque the nut (13) between to to 0.8 m.daN (70.79 lbf.in) and to 1 m.daN (88.49 lbf.in).
(7)
Put the plate (7) in the correct position on the structure of the panel 110VU (11).
(8)
Install the four screws (1).
(9)
Install the knob (2) on the shaft of the control switch (12).
1EFF : ALL 1 22-62-11Page 406 1 1 Feb 01/99 1 1 1CES 1
(10)
Lock the knob (2) with the two screws (3).
(11)
Install the knob (4) (in the OFF position), the pin (6) and the screw (5).
Subtask 22-62-11-420-051
B. Installation of the Panel 110VU
(Ref. Fig. 401/TASK 22-62-11-991-002)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM AUTO FLIGHT 自动飞行2(21)
