4. Procedure
_________ Subtask 11-00-00-915-059
A. Installation of the Decal
(1)
Put the decal in the preparation and let it for 15 to 20 seconds.
(2)
Install the decal with the face which has the markings against the contact surface.
EFF : ALL
11-00-00Page 223
May 01/05
R
CES
(3)
Press one of the ends of the decal against the support and pull the other end upwards to prevent formation of wrinkles.
(4)
Press the decal against the surface with a plastic scraper. Start from the center and press towards the edges. Be careful to prevent formation of wrinkles or air pockets. To complete the operation apply a strong pressure on all the surface with a rubber roller.
(5)
As you do these operations, remove the unwanted solution with a moist sponge.
(6)
Apply the moist sponge to the backing paper of the decal.
(7)
After 2 minutes, remove the backing paper.
(8)
Remove the remaining compound from the decal surface and around the decal with a sponge soaked in water.
(9)
Make holes in the air pockets, if any, with a needle.
(10) If the installation is incorrect:
(a)
If the decal is moist:
-remove the decal and do the procedure again with a new decal.
(b)
If the decal is dry:
-apply a MISCELLANEOUS (Material No. 19-003) soaked in CLEANING AGENTS (Material No. 11-003) on the decal, then remove the decal with plastic scraper or CLEANING AGENTS (Material No. 11-016).
NOTE : The decal is bonded after 3 or 4 days. During this time,
____ do not clean the decal area.
R **ON A/C 001-002, 051-052, 151-199, 301-399, 401-499,
Subtask 11-00-00-916-051
B. Protection of the Decals in Areas on which Fluid can Fall (Fuel, Hydraulic Fluid)
(1) Apply PAINTS FOR DETAIL (INTERNAL AND EXTERN AL) (Material No. 07-017) on the decal with a soft hair brush.
EFF : ALL
11-00-00Page 224
Aug 01/05
CES R **ON A/C 003-049, 053-099, 101-149, 201-299,
Subtask 11-00-00-916-051-A
B. Protection of exterior markings
(1) Apply a PAINTS FOR DETAIL (INTERNAL AND EXTERN AL) (Material No. 07-018) on all exterior functional and maintenance markings.
**ON A/C ALL
5. Close-up
________
Subtask 11-00-00-942-050
A. Make sure that the work area is clean and clear of tool(s) and other items.
EFF : ALL
11-00-00Page 225
May 01/05
CES TASK 11-00-00-400-011
Installation of the Metal Identification Plates
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 09-002 USA MIL-S-8802 TYPE I CLASS B FUEL TANK SEALANTPOLYSULFID(NO LONGER AVAILABLE (Ref. 20-31-00)
Material No. 09-016 USA MIL-PRF-81733D TYPE II CLASS B CORROSION INHIBITING FILLET CONSISTENCY (Ref. 20-31-00)
Material No. 11-003 USA ASTM D 740 METHYL-ETHYL-KETONE (Ref. 20-31-00) Material No. 11-016 USA BOEING BAC 5000 BAC 5504 BAC 5750 CLEANING SOLVENT (Ref. 20-31-00) Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
3. Job Set-up
__________
Subtask 11-00-00-110-059
A. Cleaning of the Contact Surfaces
(1) Clean the contact surface of the placard with MISCELLANEOUS (Material No. 19-003) soaked in CLEANING AGENTS (Material No. 11-003) or CLEANING AGENTS (Material No. 11-016).
EFF : ALL
11-00-00Page 226
May 01/05
R
CES 4. Procedure
_________ Subtask 11-00-00-915-060
A. Installation of the Placard NOTE : This installation procedure only applies to plate bonding. To know
____ if you must bond or rivet the plate, refer to the Standard Manual.
(1)
Apply SEALANTS (Material No. 09-002) or SEALANTS (Material No. 09-016) on the support with a soft hair brush.
(2)
Install the placard and make sure that it is correctly bonded.
(3)
Remove the unwanted compound.
5. Close-up
________ Subtask 11-00-00-942-060
A. Make sure that the work area is clean and clear of tool(s) and other items.
EFF : ALL
